I must say that the cars I have owned for the past 20 years have been extremely reliable. Perhaps we are all a little spoiled. I remember when I was starting out in the '60's, I always bought used because I couldn't afford new. I also remember spending a substantial part of my life UNDER the car replacing: Exhaust system ,about once a year, points...Maybe not all of you are old enough to know about points, condensers, ignition coils, replaced every 3000 miles, plugs re-gapped every 1000 miles , engine overhaul at 40,000......should I go on?
I have driven my last 5 cars in excess of 80,000 miles without as much as one tune-up and no other problems that I can think of that wasn't covered by warantee.
I know we owe Japanese quality (invented by an American by the way) for what we have today along with competition.
I feel like an old fogey with this comment; but it seems that the electronics revolution translates into a chance for the repair shops to charge whatever they feel like for repairs. Two real stories both involving my wife's cars - one had a faulty sensor that required replacement of the entire engine (I kid you not - fortunately it was under warranty) and recently a thermostat replacement cost $700 - not under warranty. Now granted, newer cars are much more sophisticated and fuel effecient than the cars of 30 years ago - but sometimes it would be nice to know that if your car dies you can clean up the sparkplugs with a wire brush and gap the points with a piece of cardboard and get it running again.
The Grand Prix isn't much of a family car. No place to put your luggage, the mileage stinks, the shock absorbers are lousy, the CD player is non-existant, and it is a magnet for the police! They need to go back to the drawing board...
At the dawn of this new millennium, (circa Y2K) when advance development teams were brainstorming radical new concepts of integrating GPS, BT, MP3 via USB, WiFi, Large-color LCD-screens, and other "radically new ideas" into the automotive sector, electronics engineers were somewhat chastised by automotive engineers for crowding into their space. After all, the V8 and the automatic transmissions were established mechanical wonders with over half a century of implemented use."Surely this new electronic stuff is just a passing fad --- its kinda cool, but really, who would want all that electronic gizmo stuff – it only distracts from the driving experience".
Thank goodness the automotive sector DID adapt, since their legacy is often backward looking.
Driving, no. Sitting in lots of them, yes. Getting into a Smart car and closing the door is an experience. Not exactly a heavy thud. Sensors were definitely on the agenda there, in that they're not visible but if you go to the automaker people, they will talk about them. Anyway, the electronics evolution is well along on the automotive platform.
hey Alex - did you get to roadtest any of those babies? they are all gorgeous and fun to drive as well - but are they safe? However, one thing is for sure: I am sure there are a lot of "MEMS inside" those machines.... Karen
I enjoyed the slideshow. It was nice to see what is coming down the pipeline. But where are the other US automakers. Half of those were old cars and don't get me wrong I love seeing old cars. Too bad no brass era cars in there or a speedsteer with an airplane engine in it. Those are even more neat to see. :) I realize the show name has international in it, but Ford seems to have been present. Hey, have any more pics of Honda's NASCAR engine? Is it tuned port or direct injection? Looks like it's a dual overhead cam engine and a direct inject, but never can see any really up close pics of one of the engines.
UK-based Plastic Logic and French company ISORG have created what the pair tout as a first in flexible printed electronics: a large area, conformable, organic image sensor printed on plastic.
For 3D printing to make the jump from rapid prototyping to manufacturing, engineers will need to find easier ways to move products from their CAD screens to their printers.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
0 
