<<  <  Page 3/4  >  >>
User Rank
Battar   4/4/2012 9:14:50 AM
So you used company time and company parts for you own private work? Doesn't sound right, unless you did it after hours (and you're not paid hourly).

User Rank
Good going!
notarboca   4/4/2012 1:03:07 AM
Bully for you, John!  I have to take every broken thing apart (within reason) to see if I can fix it.  Glad you were successful!

User Rank
Re: Keep it simple
richdertec   4/3/2012 6:48:50 PM
I designed and built a solar hot water controler back in the early 80's. It is also of analog design and built and tested to UL standards. I built a total of 50 units, all of which are still operating (to my knowledge) to this day. No one has complained. Several of them, including mine, had to have the wires to the panel sensor replaced due to UV damage. The pump is controlled using a TRIAC in place of a relay. Troubleshooting and replacing defective components is easy on the double-sided board, and parts are still available to this day.

User Rank
Case of the Fried Solar Heater Controller
HRBDESIGN   4/3/2012 5:45:52 PM
I had a simular experiance with my solar pool heater.  The controler stopped working, I removed the controller from the circuit and found the power relay tha operated the water valve was defective.  I went on line to find the part. The venders had a $50 mimium order so it was prohibitively expensive so I bought a new control;ler for $100.  Problem solved!

User Rank
Repair of non repairable parts
sdgengineer   4/3/2012 5:34:28 PM
Reminds me when I had a VW Diesel Rabbit.  The car ran well, but one time a water leak got in the glow plug time delay relay.  It failed and I had to lift the hood and apply a jumper between the battery and the glow plug bus for 30 seconds or so to get the car started.  I checked the VW dealer and a new plug in relay was $35 a lot in 1985.  So I took the old relay apart, and replaced the comparator ICs, which cost less than $1 each, but with shipping ended up costing $4.  It was good for the rest of the car's life.  


S D Gardner, P.E.

User Rank
I let the neigbour borrow the multimeter did I just kill him
wbswenberg   4/3/2012 5:09:30 PM
I'm watching my favorite program and there is a knock on the door.  My neighour needs leads for his multimeter.  I lend him the whole Harbour Freight special with clamp on ammeter with a breif explaination.

Then I think, he knows enought to to pull the plug, right.  He is trouble shooting his electric dryer.  I had to check.  Yes, he knows.  We looked a lot of the part.  The schematic used non standard symbols but we figure out what was what. 

I mensioned that what works is as important was what does not work.  It does not do any thing.  Oh, yes the door light comes on and the clock works runs.  I showed him how to jumper around components. I explained the schematic some what.  With a half hour we found the thermal limit component that we jumped allowing the other phase to power the motor.

He went on line and found the component.  He phone a friend in the business who had the part.  He replace the part and had the dryer running about an hour and half after I started. 

He thinks I should go into the business.  I think it could never pay enought fixing things rather than Oh its broke and cant be repaired I'll sell you a new one.  Just too honest.  An not worth my time.  But it was fun.

Rob Spiegel
User Rank
Re: Fixing those non-user-serviceable products
Rob Spiegel   4/3/2012 4:17:22 PM
Thanks Larry,

Wow, you're still working on the tornado destruction of 2011, nearly a year later. All the best on that.

Larry M
User Rank
Re: Fixing those non-user-serviceable products
Larry M   4/3/2012 4:14:31 PM

I forgot to mention the Mitsubishi ECM (car engine control module "computer") which needed four inexpensive capacitors and some jumper wired where PCB traces had been eaten through by poorly-selected capacitor adhesive. That baby would have cost $700, had I not been able to install about $4.75 worth of capacitors.

And the dishwasher control which was over $12, but not available, fixed with a couple of "bullet" connectors costing pennies.

And I already promised to write you about the GM high-mounted brakelights. They will have to be a destructive analysis. I tried to open them to effect a repair but they were bonded (ultrasonically welded? epoxied?) so well that I will have to break them apart to find out what failed.

Terribly busy right now--besides my day job I'm leading the volunteer recovery effort from the tornados which struck here on April 16, 2011. This consumes all my nights, but it's nearly done. I should be able to send you something in May or June.


Rob Spiegel
User Rank
Re: Fixing those non-user-serviceable products
Rob Spiegel   4/3/2012 3:52:30 PM
Hey Larry,

We'd love to use some of your stories at Sherlock Ohms postings. Could you send one or two of them along? They need to be at least 350 words, and we also need a shor bio to go along with it -- about two to four sentences would be find.

You can send you story to Rob.spiegel@ubm.com


Larry M
User Rank
Fixing those non-user-serviceable products
Larry M   4/3/2012 3:36:42 PM
I've lost track of all the non-user-serviceable products and components I've fixed.

There was the PC motherboard which wouldn't drive the printer.  Had to replace a surface-mount IC on it.

The 1984 washer that was incredibly robust but stopped working in 2008. It would never progress from the washing cycle to drain, fill, and rinse.  The controller board would have cost $350, except you couldn't even get them. The triac which fixed it cost 37 cents from Mouser.

Two Roombas, each of which had failures in the battery charger. Each took two surface mount transistors (didn't bother to figure out which one had failed).

The loss of innocence of my son, at about age 12:
"Dad, this stereo receiver is dead. It won't go on. Nothing at all."
"Son, get a #2 Phillips screwdriver from the workbench."
"Dad, the label says 'No user serviceable parts inside.'"
"Yes, son. no user serviceable parts inside." as screws are removed from the cover.
"Son, no user serviceable parts inside," as the cover is lifted off, revealing a blown glass cartridge fuse in clips, in plain sight at the top of the unit.

My son is now 37. I'm still using the receiver, haven't had to change the fuse a second time yet.

The $1.50 picofuse that put the $200 laser printer back into service in 2005 or so. Still using it.

There are dozen more instances, but they all follow the  same pattern. If you simply think a little, you can replace inexpensive components instead of expensive assemblies or complete products.

<<  <  Page 3/4  >  >>

Partner Zone
Latest Analysis
Governmental policies and mandates in Europe are leading the way in creating low-carbon manufacturing.
Digital healthcare devices and wearable electronic products need to be thoroughly tested, lest they live short, ignominious lives, an expert will tell attendees at UBM’s upcoming Designers of Things conference in San Jose, Calif.
Designers of electronic interfaces will need to be prepared to incorporate haptics in next generation products, an expert will tell attendees at the upcoming Designers of Things conference in San Jose, Calif.
According to a Randstad Engineering compilation of salary studies, engineering salaries are increasing beyond inflation, with employers paying to keep potential suitors away from their employees.
The company says it anticipates high-definition video for home security and other uses will be the next mature technology integrated into the IoT domain, hence the introduction of its MatrixCam devkit.
Design News Webinar Series
11/10/2015 11:00 a.m. California / 2:00 p.m. New York
10/29/2015 11:00 a.m. California / 2:00 p.m. New York
10/20/2015 8:00 a.m. California / 11:00 a.m. New York
12/2/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jul 6 - 10, Building Raspberry Pi Controllers with Python
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service