Great project. I think a piece of red plastic over the display would enhance its visibility during daylight. I had the same problem with an LED digital clock I built many years ago. The red plastic sheet over the display improved it a lot.
Alternatively, a cheap level switch hooked to a logic input.
Lay it on it's side to turn it off. Set it upright to turn it on.
A quick flip (so the level switch toggles off then back on before the unit can turn itself off) could reset the timer. A slower flip does something else.
Want to get fancy? Two level switches. Set it upright for a timer. Set it upside down and it's a clock (software would have to rearrange the segments).
I have thought about replacing the mode switch with a Hall effect switch and avoiding one seal. i haven't used magnetic reed switches, but looking at some data I think they might work for the power switch. It would be an improvement if I can eliminate both switch seals completely. I'm going to look into making that change.
Adding the rechargeable batteries and inductive charger would probably add more cost and complexity than this project would merit. It also means separating the timer from the rest of my swim gear to charge it and then remembering to put it back before going to the pool.
The timer uses four o-rings to seal out the water. Two of the o-rings are visible on the white plastic end caps. The other two o-rings seal the rotary shafts that actuate the two switches. To open the case for battery replacement you need to twist and pull the cap off. The o-ring seal is pretty tight so this can be difficult. An improvement would be to add a better gripping surface on the end caps. Currently I put the plastic end cap in a vice and twist the clear polycarbonate body. As you can probably imagine, i've had the cap off many times during development. It doesn't compromise the seal.
One hundred hours on 4 AA batteries. Not bad for an active LED display. This could be turned into a manufactured product with a couple of minor changes so the case's integrity would never have to be breached.
1) Replace the through shaft switches with magnetic proximity detection, either Hall effect devices or reed switches with magnetic actuator buttons or a magnet on a lanyard on the outside of the case.
2) Replace the alkaline primary cell batteries with rechargeable cells, charging circuit and induction coil.
Place the unit in a magentically coupled charging station between uses.
One gotya with secondary cells is to be sure there is a safety vent mechanism in the waterproof case to prevent pressure buildup should the batteries outgas.
The website at the end of the video shows how he made it waterproof.
http://dougsdiy.com/
Excerpt from that page:
To use this timer I needed two switches accessible from the outside. I also needed to see the LED display yet protect it from water. That led me to a design where the entire system is housed in a waterproof case made from a polycarbonate tube with acetal (a type of plastic) end caps. The two end caps are sealed with the polycarbonate tube by using two O-rings (the black rings in the photos). Only the switches need to penetrate the end caps.
While many of Design News' Gadget Freak projects are cool and useful to the person creating them, this is one that really could be mass produced and put on the market. Doug, how did you seal the case to make it waterproof? Also, once the batteries run out, is there a way to replace them without compromising the waterproof nature of the clock?
I was taken with the nightswimming, too, Beth. It's quite impressive. What a way to start the day. It's also inspiring to see he created a gadget to support his commitment to health.
Forget about Doug's innovative work creating a digital timer leveraging LED displays. How about the fact that Doug and crew are up swimming in an outdoor pool well before the light of day. I'm shivering and cold just thinking about it. So frankly, I have to applaud that effort, Doug, and I admit, your gadget is pretty nifty!
We looked at a number of sources to determine this year's greenest cars, from KBB to automotive trade magazines to environmental organizations. These 14 cars emerged as being great at either stretching fuel or reducing carbon footprint.
Researchers at MIT and Sandia National Labs have observed a reaction in lithium-air batteries that could help improve the design of these cells for electric vehicles and other applications.
Healthcare might seem to be an unlikely target application for the Internet of Things technology, but recent developments show small ways that big-data is going to make an impact on patient care moving into the future.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
