Interesting deductions, but this failure was in 1974 after owning the boat for only 6 years.
Through-hull fittings, seacocks, propellers, and shafts are all commodity products, whereas the forestay fittings were made at the factory.
Stray current corrosion can occur on any metal. This is what occurs when your shore-power cord is plugged in at all times. ESPECIALLY if some joker connects the white neutral (current-carrying conductor) to the green safety ground.
GALVANIC corrosion is due to dissimilar metals immersed in an electrolyte. This is where the "de-zincification" can eat you alive.
Many alloys contain a little zinc (<5%), but when the content approaches 25-35% the de-zincification can weaken the material to the consistency of a sponge.
This whole thread makes me feel good that I can only afford a Fish & Ski rather than such a fancy rig as this. My main corrosion problem is rusty fish hooks on favorite plugs and they are easy to replace.
My experience with the American Brass & Bronze industry has not impressed me with their quality and ethics. The bearing manufacturing I work for purchases a lot of Centrifugally Cast Bronze for bearing cages. This is preferred because centrifugally cast alloys claim "wrought" strength properties that are higher than simply cast versions. When a rash of cage structural failures occurred, we had the remains analyzed for chemistry and structure, both of which turned out "acceptable." We decided to order a few large blanks from which "dog bone" tensile specimans could be machined and tested. Ultimate (tensile) strength came back somewhat lower than claimed, so we filed a complaint with the supplier. Their response was that their product was not deficient because the industry specification that they follow allows them to keep trying new test speicmens until they obtain a group that passes. (The industry writes its own specs.) In the end we resolved ourselves to an addage frequently heard in old Western movies, "Yes, we know the game is crooked, but it's the only game in town."
@steveod21: Muntz metal is a particular kind of brass called a duplex brass. Like most other kinds of brass, it is susceptible to dezincification, but since sheathing was not structural, this may not have been considered to be very important. More important were its antifouling properties -- barnacles, seaweed, algae, and other marine life don't like to attach themselves to copper, or to copper alloys such as brass. The development of antifouling paints (most of which contain copper) brought an end to the era of metal sheathing.
Naval brass, which I described below, is very similar to Muntz metal, except for the addition of a small amount of tin (and sometimes some other elements) to prevent dezincification.
Although it is subject to dezincification, Muntz metal is resistant to many other kinds of corrosion, so it is still used in some applications.
I'm not an expert on metals, but I couldn't help recalling how an Englishman (with a fairly un-English name) made his fortune by developing an alloy of copper and zinc which came to be known as 'Yellow Metal' (or Muntz metal, after its creator). This was used extensively in ships, and clipper ships particularly as it happens, and the Cutty Sark and Thermopylae were full of it. Cheaper and stronger than copper alone, it was even used for bolts in some applications although its main use seems to have been for sheathing.
See http://en.wikipedia.org/wiki/Muntz_metal. It was the comments about battery electrodes that I found strange as Yellow Metal seems to have been in great demand for maritime applications in the 19th and early 20th centuries.
The Article doesn't say when this took place, but seems to imply a recent event.
Cheoy Lee's coming out of the Kao Shung yard in HK were known to have crappy metal fittings. Lifeline stanchions and pulpit/pushpit are likely out of 303 or 304 stainless, not marine grade 316. As a result, pitting and corrosion, and premature structural failure are known endemic problems with those vessels.
The author's uncle is lucky the fitting didn't fail when under dynamic load, or he would have lost the stick.
Yes, checking all underwater fittings each haul-out is important. The dolphin striker is a rod or cable that goes from the outward end of the bowsprit to a fitting, usually underwater, on the bow of the boat. There is no reason to disassemble this part except for the occasional inspection for corrosion. The part doesn't move and for the most part would be considered a permanent fixture - until it breaks. Most underwater hardware is designed to be taken-apart and cleaned, lubricated or inspected fairly easily and it is really unlikely that a turnbuckle on a dolphin striker would be made of an inferior alloy unless it was installed at some later date. I don't think I have ever seen a soft-brass turnbuckle or pin outside of a novelty shop.
@Rob: As one of the articles I linked to mentions, one telltale sign of dezincification is a loose, powdery white deposit. This is usually zinc oxide or zinc chloride, which are corrosion products of zinc. (Of course, in a marine environment, a white deposit might also be left by salt).
Using a 3D printer, CNC router, and existing powertrain components, a team of engineers is building an electric car from scratch on the floor of the International Manufacturing Technology Show in Chicago this week.
In November, a European space probe will try to land on the surface of a comet moving at about 84,000 mph and rotating with a period of 12.7 hours. Many factors make positioning the probe for the landing an engineering challenge.
NinjaFlex flexible 3D printing filament made from thermoplastic elastomers is available in a growing assortment of colors, most recently gold and silver. It's flexible and harder than you'd expect: around 85A (Shore A).
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.