I was just giving an example of a CFL that turns on instantly. Your article did not specify the unusually high light levels that you required and that this was the reason to select specific CFL, which apparently start slow. What kind of work is done in your shop that requires such high light levels?
I'm sure that there are other solutions. I needed floodlights of 1000 lumens or more and total wattage of 200 or less. There aren't many CFLs available in that category. I suppose there may be some that brighten faster.
GE actually makes a hybrid lamp with a halogen bulb in the center of a CFL that works much like this. But not in a floodlamp configuration, and they are more costly.
How about testing a few CFLs until you find the ones that turn on instantly?
I have seen s-l-o-w starting CFLs and I have seen fluorescents with electronic controllers that start full brightness immediately when turned on. I even have one as a flashlight / emergency light that sits plugged into AC and the same moment that the grid power goes out (which is too often here) the light comes on full brightness. The lamp has no marking but it is a folded CFL tube of an estimated 10-15W, so very bright floodlight, operated from a built-in 6V sealed lead-acid battery by a small inverter board that also keeps the battery charged.
I have always converted every house I moved into since the CFLs became popular to as much CFL-only as possible and saved tons of money on power bills, even including the initial purchase of the lamps. I started to add some LED into the mix since a year, but still find too many failures from cheap Chinese manufacturing and bad design.
Not saying that this gadget is not useful, but it feels a bit like a kludge - an unnecessary complicated solution. But maybe this was simpler than buying new / the right type CLF, I don't know.
Good to see someone sat down to build one, but this already exists... It's called a Quartz restrike, and is used where you need light when you have metal halide or other arc discharge lamps that may go out due to frequent poewr fluctuations.
For the case of the homeowner though, wouldn't it just be cheaper to just use the incandescent and turn it down?
Wow, @Dick, that is really nifty! We have CFLs in the restrooms of our new science building. They are on a motion-sensor switch / timer that energizes them on entry. Not that you need lots of light for detailed work, but the room does take around 40 seconds to turn from an eerie yellow to solar white. The biggest problem is that the motion sensor cannot see down into the stalls... so if you bring along reading material, you only have about 3 minutes before you have to use your cell phone as a flashlight. -- but I guess that is another problem all together. Nice work! =]
Having just moved into a new house that is "challenged" in terms of adequate outlets/lighting, I can totally empathize with his situation and could use some of that creativity in my new home, albeit with a slightly sleeker, and less obtrusive asthetic design (no offense, Dick).
For 3D printing to make the jump from rapid prototyping to manufacturing, engineers will need to find easier ways to move products from their CAD screens to their printers.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
New versions of BASF's Ecovio line are both compostable and designed for either injection molding or thermoforming. These combinations are becoming more common for the single-use bioplastics used in food service and food packaging applications, but are still not widely available.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
0 
