HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
<<  <  Page 2/3  >  >>
mikey
User Rank
Iron
Re: Creative solution to inadequate lighting
mikey   3/31/2012 9:35:36 PM
NO RATINGS
It is my understanding that flourescent lights are life limited by two things: hours of use and number of starts. For that reason automatic light sensors should have a longer "hang time", leaving the lamps on for as much as 30 minutes once they are lit. Incadescent lamps are much less sensitive to starts (although they, too, typically fail at start) and so can be set for much shorter hang times to save on the electricity.

Tim
User Rank
Platinum
Engineering
Tim   3/30/2012 9:55:42 PM
NO RATINGS
Great job using engineering to solve your own problem. So many times, engineering solutions are reserved for "work" that the y are forgotten at home

Charles Murray
User Rank
Blogger
Garage shop
Charles Murray   3/30/2012 7:21:13 PM
NO RATINGS
Kudos to Dick for a job well done. There's nothing like a good garage shop. I have a friend who's an engineer who spends more time in his garage shop than in his house, even during Chicago winters.

BRedmond
User Rank
Silver
Re: Homemade version of what's already built.
BRedmond   3/30/2012 11:23:28 AM
NO RATINGS
I'm a bit of a lamp snob; I'll only buy from the "big 3," GE, Philips and Sylvania for quality reasons.  I too have been installing CFLs in my house since they firsat started becoming available and my utility offered rebates (no longer available) to try to make them economically viable.  I haven't been able to put them yet in any fixture served by a dimmer switch and I discovered a long time ago that they fail quickly if they are switched on and off a lot so I don't have them in my walk-in closet.  In my vanity light bars, I mix CFLs 50-50 with incandescents because of the warmup time.  I have a 42W spiral CFL burning base up in my laundry room and my family complains about the time required to come to full lumens.  Dick doesn't say how well insulated his garage is or where he lives but my garage might be too cold for 1/4 - 1/2 of the year for the CFLs (or the linears that somebody else mentioned) to come up to full lumens quickly. 

Droid
User Rank
Platinum
Apply Gradual Dimming to Car Headlights
Droid   3/30/2012 9:23:06 AM
NO RATINGS
Makes me think of another idea.  Maybe its already out there and I haven't noticed, but why not use gradual dimming and brightning for car headlights.  Seem like a concept that would be a very welcome chance to the sudden flash seen when switching between high/low beam. 

apresher
User Rank
Blogger
Dimming Bulb
apresher   3/29/2012 4:58:20 PM
NO RATINGS
Love Gadget Freak because it shows the real ingenuity of DN readers. Necessity is the mother of invention.

DickB
User Rank
Iron
Re: Homemade version of what's already built.
DickB   3/29/2012 3:44:45 PM
NO RATINGS
No doubt there are other solutions.  The floods are a good choice for aiming light where it is needed.  For example, two are pointed towards the garage door area to illuminate that area of the garage, even though the lamps themselves are some distance from the door in order to be clear of the door when it is raised.  Although I could have installed low-profile tubes directly over that area, they would have been covered by the raised overhead garage door, and I would have had a potential dark spot.

Rob Spiegel
User Rank
Blogger
Re: Homemade version of what's already built.
Rob Spiegel   3/29/2012 3:34:25 PM
NO RATINGS
From your responses to comments, Dick, it sounds like the light you created was the ideal solution to your lighting needs -- given what was available. Thus, it makes for a great gadget, one that meets specific needs in ways that no other solution on the market can.

cvandewater
User Rank
Gold
Re: Homemade version of what's already built.
cvandewater   3/29/2012 3:26:32 PM
NO RATINGS
"TL" fluorescent tubes are typically mounted on a carrier but those can be very low profile and you can feed the wires from any side. I have here a TL variant that is less than 1" total height (carrier with build-in electronic starter + tube).

The entire assembly (carrier + tube) clicks into two small brackets that you screw to the mounting surface and there is a plug on either side of the carrier to power it.

I don't see how this would be worse than the plastic rails for wire distribution to boxes with screw fittings for floodlights.

DickB
User Rank
Iron
Re: Homemade version of what's already built.
DickB   3/29/2012 2:34:14 PM
NO RATINGS
The shop is used mostly for woodworking and finishing. Often conventional fluorescent tubes are used in wood shops, but I believe that they would have been more difficult to install in my case.

<<  <  Page 2/3  >  >>


Partner Zone
Latest Analysis
A bold, gold, open-air coupe may not be the ticket to automotive nirvana for every consumer, but Lexus’ LF-C2 concept car certainly turned heads at the recent Los Angeles Auto Show. What’s more, it may provide a glimpse of the luxury automaker’s future.
Perhaps you didn't know that there are a variety of classes, both live and archived, offered via the Design News Continuing Education Center (CEC) sponsored by Digi-Key? The best part – they are free!
Engineer comic Don McMillan explains the fun engineers have with team-building exercises. Can you relate?
The complexity of diesel engines means optimizing their performance requires a large amount of experimentation. Computational fluid dynamics (CFD) is a very useful and intuitive tool in this, and cold flow analysis using CFD is an ideal approach to study the flow characteristics without going into the details of chemical reactions occurring during the combustion.
The damage to Sony from the cyber attack seems to have been heightened by failure to follow two basic security rules.
More:Blogs|News
Design News Webinar Series
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
12/10/2014 8:00 a.m. California / 11:00 a.m. New York
11/19/2014 11:00 a.m. California / 2:00 p.m. New York
11/6/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jan 12 - 16, Programmable Logic - How do they do that?
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  67


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service