It is my understanding that flourescent lights are life limited by two things: hours of use and number of starts. For that reason automatic light sensors should have a longer "hang time", leaving the lamps on for as much as 30 minutes once they are lit. Incadescent lamps are much less sensitive to starts (although they, too, typically fail at start) and so can be set for much shorter hang times to save on the electricity.
Kudos to Dick for a job well done. There's nothing like a good garage shop. I have a friend who's an engineer who spends more time in his garage shop than in his house, even during Chicago winters.
I'm a bit of a lamp snob; I'll only buy from the "big 3," GE, Philips and Sylvania for quality reasons. I too have been installing CFLs in my house since they firsat started becoming available and my utility offered rebates (no longer available) to try to make them economically viable. I haven't been able to put them yet in any fixture served by a dimmer switch and I discovered a long time ago that they fail quickly if they are switched on and off a lot so I don't have them in my walk-in closet. In my vanity light bars, I mix CFLs 50-50 with incandescents because of the warmup time. I have a 42W spiral CFL burning base up in my laundry room and my family complains about the time required to come to full lumens. Dick doesn't say how well insulated his garage is or where he lives but my garage might be too cold for 1/4 - 1/2 of the year for the CFLs (or the linears that somebody else mentioned) to come up to full lumens quickly.
Makes me think of another idea. Maybe its already out there and I haven't noticed, but why not use gradual dimming and brightning for car headlights. Seem like a concept that would be a very welcome chance to the sudden flash seen when switching between high/low beam.
No doubt there are other solutions. The floods are a good choice for aiming light where it is needed. For example, two are pointed towards the garage door area to illuminate that area of the garage, even though the lamps themselves are some distance from the door in order to be clear of the door when it is raised. Although I could have installed low-profile tubes directly over that area, they would have been covered by the raised overhead garage door, and I would have had a potential dark spot.
From your responses to comments, Dick, it sounds like the light you created was the ideal solution to your lighting needs -- given what was available. Thus, it makes for a great gadget, one that meets specific needs in ways that no other solution on the market can.
"TL" fluorescent tubes are typically mounted on a carrier but those can be very low profile and you can feed the wires from any side. I have here a TL variant that is less than 1" total height (carrier with build-in electronic starter + tube).
The entire assembly (carrier + tube) clicks into two small brackets that you screw to the mounting surface and there is a plug on either side of the carrier to power it.
I don't see how this would be worse than the plastic rails for wire distribution to boxes with screw fittings for floodlights.
The shop is used mostly for woodworking and finishing. Often conventional fluorescent tubes are used in wood shops, but I believe that they would have been more difficult to install in my case.
By experimenting with the photovoltaic reaction in solar cells, researchers at MIT have made a breakthrough in energy efficiency that significantly pushes the boundaries of current commercial cells on the market.
In a world that's going green, industrial operations have a problem: Their processes involve materials that are potentially toxic, flammable, corrosive, or reactive. If improperly managed, this can precipitate dangerous health and environmental consequences.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
