HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Comments
View Comments: Newest First|Oldest First|Threaded View
tekochip
User Rank
Platinum
Gamma Sterilization
tekochip   4/14/2012 9:26:02 AM
NO RATINGS
Another great advantage of FRAM is that it will hold up to gamma sterilization.

Charles Murray
User Rank
Blogger
Re: More info about FRAM technology
Charles Murray   4/13/2012 6:41:44 PM
NO RATINGS
FRAM is also getting used used in remote structural monitoring applications -- bridges, buildings, etc -- because it provides a 250X power savings.

http://www.designnews.com/document.asp?doc_id=230477

Jon Titus
User Rank
Blogger
More info about FRAM technology
Jon Titus   4/3/2012 11:05:07 AM
NO RATINGS
Wikipedia has a good article about FRAM technology and it notes Ramton has worked with Texas Instruments for over 10 years, so that also might explain TI's interest in replacing high-power Flash memory and SRAM with FRAM. See: http://en.wikipedia.org/wiki/Ferroelectric_RAM.

Ann R. Thryft
User Rank
Blogger
Re: Why FRAM?
Ann R. Thryft   4/3/2012 9:03:02 AM
NO RATINGS

Thanks, Jon, for that info. That makes sense. Back in the day when I covered memory, I used to wish I could write more about FRAM since it seemed like such a nifty technology for specific applications. That adjustable partitioning looks especially useful.


Jon Titus
User Rank
Blogger
Re: Why FRAM?
Jon Titus   4/2/2012 12:11:32 PM
NO RATINGS
Hi,Ann.  I bet TI put the FRAM in the MSP430 first because this MCU appeals to engineers who need to save as much power as possible. Because the FRAM operates from a 1.5-volt supply, it doesn't require a charge-pump circuit to produce the higher voltage needed by flash memory. That saves energy right away. According to TI, the FRAM section reduces memory power use by a factor of as high as 250 times. The FRAM also has faster throughput for read/write cycles and a very long life for such cycles.  One additional capability--as noted already in a comment--gives programmers the capability to divide memory as they choose and adjust the partition as storage needs change. The entire memory-address range operates within the FRAM. So if you need only 1 kbyte of storage for temporary data, you can have 15 kbytes left for a program.

Ann R. Thryft
User Rank
Blogger
Re: Why FRAM?
Ann R. Thryft   3/29/2012 12:42:50 PM
NO RATINGS

Thanks, tekochip and Chuck. I didn't realize that licensing issues were one of, if not the, major hindrance to wider adoption of FRAM. I'm still curious to know why TI put it in this MCU vs some other one.


Charles Murray
User Rank
Blogger
Re: Why FRAM?
Charles Murray   3/28/2012 8:01:13 PM
NO RATINGS
I agree, Ann. Everybody on the electronics and materials beats seemed to be writing about FRAM for a decade before anything happend. TI finally incorporated it into a microcontroller about a year ago.

http://www.designnews.com/document.asp?doc_id=230477

Charles Murray
User Rank
Blogger
Re: Why FRAM?
Charles Murray   3/28/2012 7:55:42 PM
NO RATINGS
MSP430 continues to push the state of the art in power consumption. Interesting that they chose the name "Wolverine," although it apparently did not help the University of Michigan during March Madness.

tekochip
User Rank
Platinum
Re: Why FRAM?
tekochip   3/28/2012 4:08:08 PM
NO RATINGS
I believe using FRAM came from Ramtron finally being able to free up its licensing and other business concerns. I was fortunate enough to use a FRAM part recently and it performed exactly as described on the label. Other than the low current capability the technology also allows you to have a very free memory map, and interesting features like self-modifying code. TI really has something, rather than just introducing a faster/smarter micro, they truly have a new innovation.


Ann R. Thryft
User Rank
Blogger
Why FRAM?
Ann R. Thryft   3/28/2012 12:21:13 PM
NO RATINGS

Jon, interesting that the MSP430 Wolverine uses FRAM. I remember writing about this memory type years ago, but it never seemed to catch on in a big way although its benefits were obvious. Any idea if that's changed? Or why TI chose it for this specific MCU? 




Partner Zone
Latest Analysis
Here are some of the top-paying jobs available to engineers as they grow in their careers.
As manufacturers add new technologies to their products, designing for compliance becomes more difficult. Prepare for the certification testing process. Otherwise, you increase the risk of discovering a safety issue after a product leaves the assembly line. That will cause significant time-to-market delays, be much costlier to fix, and damage your brand in the eyes of customers. 
Stratasys will be exhibiting two groundbreaking large-scale additive manufacturing technologies, as well as other new products, next month at the International Manufacturing Technology Show (IMTS) in Chicago.
Ford Motor Co. announced plans last week to join an ever-growing number of automakers who intend to produce fully autonomous vehicles in the next five years.
Two new technologies from Stratasys, created in partnership with Boeing, Ford, and Siemens, will bring accurate, repeatable manufacturing of very large thermoplastic end products, and much bigger composite parts, onto the factory floor for industries including automotive and aerospace.
More:Blogs|News
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9 | 10


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Technology Marketplace

Copyright © 2016 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service