As mentioned earlier, repeated stresses/cycles on an assembly are a major contributor to fatigue and crack propagation. The biggest contributor to repeated cycles is vibration. Sometimes it's difficult to observe, but even high frequency vibration (though very small displacements) can be a fatigue factor due to their high cycle rate.
Vibration can be an issue when attaching a component to a moving machine (frequency depends on the machine dynamics), when designed to handle siesmic vibrations near fault lines (relatively low frequency <10Hz), or just designing to handle transportation to the end user (between 2-500Hz). The frequency and amplitudes vary, but the main goal is to design components with resonant frequencies well above what the sample will see while in use or transport, and when designing machinery, to avoid stacking resonant frequencies so the components aren't exciting each other's resonant frequencies while in use.
@Mydesign: You're right that loads redistribute to a certain extent as a result of localized yielding, so that a linear FEA which predicts a stress greater than the yield strength in a small region doesn't necessarily indicate failure of the component. This is why designing to "get the red out" of a FEA model, without any insight into the physical situation, can result in overdesign. On the other hand, stresses below the yield strength can lead to fatigue failure if they are repeatedly applied. To get a handle on fatigue, it's important to know how the loads on a part vary over time. This is what I will discuss in the next installment.
Dave, I think the weight is eventually distributed across the area, and then it can bear more weight than concentrate to particular points. I think in most of the industrial wing, the stress tests are doing for a mass areas rather than stress test in cubic/cm sqd.
@Chuck: Other engineers should feel free to weigh in on this, but in my experience, it's most common to design to the yield strength, with an appropriate factor of safety. Doing this should protect you against overload failures, provided that (as I pointed out in the article) the loads are what you think they are, and the yield strength is what you think it is.
Dave: In the kinds of parts that are mentioned here, such as the brake cam, are the parts typically designed in accordance with the yield strength of the material, or is there some "allowable stress" design method that's set forth that is not dependent on yield? If yield is not used as criteria, does it make any difference in terms of failure rates?
@Alex: Usually, a crack which grows over time is due to fatigue, which I'll cover in my next installment. (In plastic parts, cracks which grow over time could also be due to environmental stress cracking, which I've written about before. In metals, there is a phenomenon called stress corrosion cracking, which is analagous to environmental stress cracking; I might write about this later).
Based on what I've seen in my career, fatigue failures are actually far more common than overload failures. However, overload failures are the easiest to understand, which is why I wanted to cover them first.
The mechanics of fatigue are a little more complicated. As I'll discuss, a common mistake is to treat "fatigue strength" as though it's a property like yield strength or ultimate tensile strength. It's not. But the big picture is the same: you need to understand the forces that act on the part, and the properties of the material from which it is made -- as well as all of the variables which might cause either one to vary from its normal value.
Could you do an explanation in a future post of the differences between a part (say, a bracket on a car) failing due to a migrating stress fracture versus a total, quick failure where it just breaks in two? Is that the same stress dynamic in play with different outcomes, or are they different processes entirely?
Andrew Morris designed a circuit that could detect a stroke victim's groan and convert the sound into a signal so caregivers would know when help was needed.
New disc magnet motors fit into the design trend of stepping up to closed loop performance while maintaining the cost advantage of stepper motor technology.
At the Design News webinar on June 27, learn all about aluminum extrusion: designing the right shape so it costs the least, is simplest to manufacture, and best fits the application's structural requirements.
On April 21, NASA launched a novel project, putting into orbit three satellites that employ an off-the-shelf commercial smartphone as the control system.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
0 
