<<  <  Page 3/4  >  >>
 Fred Engineer
User Rank
LOTO Basics
Fred Engineer   3/14/2012 2:05:45 PM
I agree with Water.Ratz.  LOTO is the single most important safety process in any facility.  One lock, one key, for each worker.  When we do group LOTO, the Energy Owner locks out the equipment usually following a step-by-step written procedure, then locks the key or keys in a lockbox.  Then EVERY worker hangs a lock on the lockbox.  No one has a copy of an individual workers key.  Cutting off a lock requires a strict procedure including calling the employee and Division Leader approval.  Cutting off a lock or defeating a LOTO is grounds for disciplinary action.  You have to take this stuff seriously!  As Water.Ratz pointed out, the first step is LOTO training.  If anything I said is surprising, then you probably haven't been trained properly.

User Rank
Fundamentals of LOTO
water.ratz   3/14/2012 1:02:52 PM
Any persons engaged in activities requiring LOCK OUT TAG OUT should have had LOTO training. One of the VERY FIRST things you are taught in this training is that EACH person working on a given machine / system is to apply their OWN lock and tag. The ONLY person allowed to posses a key for that lock, is the person who installed the lock. NOBODY ELSE. If this fundamental premise of the LOTO system is removed, you might as well abandon it.


Enough Said!

Ann R. Thryft
User Rank
Re: When you're right, your right.
Ann R. Thryft   3/14/2012 12:45:42 PM

I think you're right, Chuck. I've had too many parallel experiences in an office environment, which is fortunately somewhat less hazardous than the environment described here. Yet dangerous enough when monkeys are involved. And Jim has a really good point--what if it was some awful caustic liquid? 

User Rank
Lock out loser
jlinstrom   3/14/2012 11:55:24 AM
same thing happened to a friend - with 2 locks! Hacksaw, machine started when all hands were luckily clear, shouts and red faces everywhere...

Some 'proud American quality craftsman' wanted to 'git er dun' and cussed out the fool who put locks on the power switches. Again, no one was fired, OSHA was not called, the pouty fool who cut the locks and started the machine was coddled back into being a team player...

I'm a EE who just walks by these big, body-crunching machines - and I know what a LOCK-OUT MEANS!! Who do these boobs listen to, besides the voices in their own heads?

Yes, fire with PLENTY of publicity, so all the rest of the dullards remember the signs and significance. How difficult can it be to understand a lock on a switch means 'leave alone, workers in danger'?   **SHEESH**

User Rank
Personal lock
rickgtoc   3/14/2012 11:47:51 AM

In the facilities in which I've worked (pulp & paper, wood products), the interpretation of lock-out/tag-out would require you to have a personal lock or locks controlling all energy sources connected to the pump and gear box.  That would include the motor as well as valves on any connected pipelines.  Furthermore, you would maintain personal control of the key to those locks (on your person, not in a gear locker or in the control room),  And there would be at least two locks on each device.  The qualified process operator who issues the work permit is required to have a lock controrolling the energy source, and each and every person who works on the job covered by the permit is required to have a personal lock in place and to have the keys in his/her personal control. Multi-lock hasps and lockout boxes are used with large jobs and during extended maintenance operations.  Any permitted worker is required to remove his/her locks before leaving the site.  The qualified operator is not permitted to unlock the process until the work permit is returned, alll worker locks are removed, and the area is inspected and deemed safe to restore to normal operation.  Non-standard lock removal (cutting off a lock when the key or key-owner is not available) is a process requiring a series of defined steps and signatures to document why the lock is being cut and how it was determined that it is safe to do so.

The underlying principle is that each person working on repair/maintenance job shall maintain personal control of keys to locks that control all energy sources that are connected to equipment on that job, and that all locked-out energy sources have been confirmed to be at a zero energy state.  Locks require tags identifying the lock owner and the work permit # for the job.

Universally keyed locks are not permitted.

In the case you describe, I suspect that the person who removed the lock would not be the only one terminated, and you might have been barred from working on the site again.  Of course you would also have been trained on the safe work permit procedures for the facility prior to being allowed in the plant to work.

I am truly glad that you were not injured in this incident.

User Rank
Safety Starts as a State of Mind
DB_Wilson   3/14/2012 10:55:55 AM
Locks and a "Lock Out, Tag Out" procedures are only a manifestation of that state of mind. 

User Rank
Re: IMMEDIATE Termination
YJ77   3/14/2012 9:48:52 AM
I've carried my own lock, 6 position scissors lock device, and tags with my cell # since the early '90s.  The only key to my lock is on my keyring in my pocket.  I don't trust plant maintenance locks because there's always a master key on the premises.  I agree with the independent reporting to OSHA, and I'm not sure I want to consult for a plant with such an attitude toward safety. 

User Rank
Re: IMMEDIATE Termination
Asteakhouse   3/14/2012 9:48:05 AM
Back in the late 60s I had a summer job at steel mill.  I was working with an experienced permanent employee doing maintenance on the backend of one of a row of reheat furnaces.  Large steel slabs were transported on rollers to the next available furnace prior to being pushed in for heating.  Getting access to where we needed to work required standing near, and periodically walking accross, the rollers.

Prior to starting work, we verified that the power to the rollers had been locked out, but back in those days the lockout consisted of a red tag tied onto the switch with string. A friend of my co-worker thought it would be funny to scare us by turning on the rollers while we were at the back of the furnace.  Unfortunaltely, he did so exactly at the instant that we needed to cross over to get some additional tools.  It was jus a matter of luck that we were both able to jump off before getting drawn into the gap between two rollers.

The joker was fired on the spot with the full blessing of the union.

Charles Murray
User Rank
Re: When you're right, your right.
Charles Murray   3/13/2012 9:57:58 PM
I agree, Ann, it is a case of "operated by monkeys." Unfortunately, this is all too easy for me to believe. When it comes to operating machinery, these kinds of violations are probably far more common than most of us would suspect.

User Rank
Grounds for immediate dismissal
JimT@Future-Product-Innovations   3/13/2012 7:05:51 PM

Its frightening to think someone could have been killed by that incident; and what a lame-brained excuse by the culprit! Grounds for dismissal, I would say, and certainly cause for an internal evaluation of safety processes.  You did not mention what the chemical in the pipeline was – could have been caustic and flowing all over you both. Your solution to carry your own locks going forward sounds like a better answer than even the most strictly enforced corrective action offered as condolence from the incident. Glad you're around today to write about it.

<<  <  Page 3/4  >  >>

Partner Zone
Latest Analysis
A small team of engineers has created a tackling dummy robot that's comparable to training with human players on the football field.
Several plastics and elastomers have come out recently for different parts of cars, as well as for multi-material medical devices and for onboard base station antenna components.
Work in embedding conductive materials into commercially available yarn could lead to energy textiles that store power for use.
A ball bearing developed for turbofan engines by FAG Aerospace of Germany and MTU Aero Engines could have other uses such as turbines, pumps, and gearbox stages.
Fifty-six-year-old Pasquale Russo has been doing metalwork for more than 30 years in a tiny southern Italy village. Many craftsmen like him brought with them fabrication skills when they came from the Old World to America.
Design News Webinar Series
8/13/2015 11:00 a.m. California / 2:00 p.m. New York
6/25/2015 11:00 a.m. California / 2:00 p.m. New York
6/24/2015 11:00 a.m. California / 2:00 p.m. New York
9/10/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Aug 31 - Sep4, Embedded System Design Techniques™ - Writing Portable and Robust Firmware in C
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Course August 25-27:
Sponsored by MICROMO
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service