HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
<<  <  Page 2/3  >  >>
Rob Spiegel
User Rank
Blogger
Re: CAE plays a role in wind turbine blade design as well
Rob Spiegel   3/13/2012 2:18:50 PM
NO RATINGS
Yes, the technology that's getting developed in one of those gov/industry/university projects works to grab winds that are not pointing in such a way as to spin stationary blades while at the same time optimizing the spin by adjusting the blade positions.

Ann R. Thryft
User Rank
Blogger
Re: Individual pitch blade control
Ann R. Thryft   3/13/2012 12:35:26 PM
NO RATINGS

Al, thanks for the added details on improving turbine blade design. And you're right, the weight reduction seems to be the big deal here for composite blades, especially as they get a lot larger.

Chuck, no data of that kind was attached to the press release, but Bayer's site is pretty extensive and they may well have MDS or other such spec info located there.


Ann R. Thryft
User Rank
Blogger
Re: CAE plays a role in wind turbine blade design as well
Ann R. Thryft   3/13/2012 12:34:24 PM
NO RATINGS

Aldo, thanks for your input on the complex algorithms required to optimize the operation and performance of components such as blades. Beth, I'd also think that motion sensors and accelerometers would probably also be involved.


Beth Stackpole
User Rank
Blogger
Re: CAE plays a role in wind turbine blade design as well
Beth Stackpole   3/13/2012 11:29:46 AM
NO RATINGS
Funny you should raise the issue of idle turbine blades. We have one fairly large wind turbine located in my town and I have say, most of the time I drive by it, it sits idle. We live in a coastal community and the wind turbine is fairly near a pretty good size river that flows directly into the Atlantic. Needless to say, coastal winds are a big deal here. Again, despite the proximity to all this, the blades are spinning far less than I ever thought they would.

That said, I imagine the turning of the blades to adapt to wind direction has to be where it's at for future development. I would guess in addition to CAD and CAE software, intelligent sensors, embedded software, and some sort of accelerometer technology would be critical, perhaps??

LouisDE
User Rank
Iron
Re: CAE plays a role in wind turbine blade design as well
LouisDE   3/13/2012 9:41:03 AM
NO RATINGS
A bit off topic, but the dynamics of blade design aside, what will harnessing wind power do to the normal flow of air and ultimately the climate? 



Aldo Agraz
User Rank
Iron
Wind power is becoming more competitive thanks to technological innovation
Aldo Agraz   3/13/2012 2:50:15 AM
NO RATINGS
Hi, this is interesting for the energy industry because wind power is highly expected to become a major source or energy for many countries. Nowadays it is very attractive for investors to invest in a wind power plant when the resource is good instead of investing in a fossil fuel utility plant. I have studied new methods for optimization of turbine components like blades by using programming techniques like genetic algorithms combined with CAD/CAE software to increase efficiency of energy conversion, reduce size and weight of components and making the technology more affordable. More information about genetic algorithms used for wind blade development can be read in the following link: http://mozart.dis.ulpgc.es/Gias/Publications/mendez-greiner.pdf

Charles Murray
User Rank
Blogger
Good numbers
Charles Murray   3/12/2012 7:18:11 PM
NO RATINGS
Great article, Ann. Any idea how the tensile fatigue and fracture toughness compare to steel?

apresher
User Rank
Blogger
Significance of Weight
apresher   3/12/2012 4:49:40 PM
NO RATINGS
I would also expect that reducing the weight of the blades could help boost overall performance. With the emphasis on offshore installations and much larger turbines, the weight of the blades is a huge factor for design, installation and maintenance.

apresher
User Rank
Blogger
Individual pitch blade control
apresher   3/12/2012 4:45:32 PM
NO RATINGS
1 saves
Blade control is one of the areas where potential technology developments  could improve the efficiency of wind turbines.  Today, most turbines are using independent pitch control where each blade is independently controlled by a servo actuator. But all of the blades respond to the same command as they go through their cycle. Individual pitch blade control provides real-time feedback from blades or monitoring devices, and one approach is to embed sensors into the blades for real time load feedback. The system closes the loop at the turbine level using that feedback to significantly reduce the load variation from blade to blade. The result is an ability to handle peak gusts better and more quickly.

Ann R. Thryft
User Rank
Blogger
Re: CAE plays a role in wind turbine blade design as well
Ann R. Thryft   3/12/2012 3:25:43 PM
NO RATINGS

Oh, I get it. I didn't realize you meant not only getting the most out of a particular gust of wind, but keeping them going in the first place, so they are turning whenever there's wind instead of staying idle just because there's wind but not going the right way.


<<  <  Page 2/3  >  >>


Partner Zone
Latest Analysis
A team from MIT's Computer Science and Artificial Intelligence Lab (CSAIL) has developed a breakthrough new multi-material 3D printer.
The trend to automation development software emphasizing configurable objects, versus structured programming, takes a step forward.
Everyone working in MEMS is chasing the ever-elusive golden wafer. But there is a moral to this story, and help is on the way.
Despite pervasive emphasis on “faster, sooner, better,” companies that have multiple design cycles a year only update their approved vendor lists on an annual basis. Maybe it's time to rethink this.
Taking energy from renewable sources, recycling existing energy, and using components that don’t need much energy at all are becoming critical industrial and consumer design criteria.
More:Blogs|News
Design News Webinar Series
8/13/2015 11:00 a.m. California / 2:00 p.m. New York
6/25/2015 11:00 a.m. California / 2:00 p.m. New York
6/24/2015 11:00 a.m. California / 2:00 p.m. New York
6/11/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Aug 31 - Sep4, Embedded System Design Techniques™ - Writing Portable and Robust Firmware in C
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service