Yes, the technology that's getting developed in one of those gov/industry/university projects works to grab winds that are not pointing in such a way as to spin stationary blades while at the same time optimizing the spin by adjusting the blade positions.
Al, thanks for the added details on improving turbine blade design. And you're right, the weight reduction seems to be the big deal here for composite blades, especially as they get a lot larger.
Chuck, no data of that kind was attached to the press release, but Bayer's site is pretty extensive and they may well have MDS or other such spec info located there.
Aldo, thanks for your input on the complex algorithms required to optimize the operation and performance of components such as blades. Beth, I'd also think that motion sensors and accelerometers would probably also be involved.
Funny you should raise the issue of idle turbine blades. We have one fairly large wind turbine located in my town and I have say, most of the time I drive by it, it sits idle. We live in a coastal community and the wind turbine is fairly near a pretty good size river that flows directly into the Atlantic. Needless to say, coastal winds are a big deal here. Again, despite the proximity to all this, the blades are spinning far less than I ever thought they would.
That said, I imagine the turning of the blades to adapt to wind direction has to be where it's at for future development. I would guess in addition to CAD and CAE software, intelligent sensors, embedded software, and some sort of accelerometer technology would be critical, perhaps??
Hi, this is interesting for the energy industry because wind power is highly expected to become a major source or energy for many countries. Nowadays it is very attractive for investors to invest in a wind power plant when the resource is good instead of investing in a fossil fuel utility plant. I have studied new methods for optimization of turbine components like blades by using programming techniques like genetic algorithms combined with CAD/CAE software to increase efficiency of energy conversion, reduce size and weight of components and making the technology more affordable. More information about genetic algorithms used for wind blade development can be read in the following link: http://mozart.dis.ulpgc.es/Gias/Publications/mendez-greiner.pdf
I would also expect that reducing the weight of the blades could help boost overall performance. With the emphasis on offshore installations and much larger turbines, the weight of the blades is a huge factor for design, installation and maintenance.
Blade control is one of the areas where potential technology developments could improve the efficiency of wind turbines. Today, most turbines are using independent pitch control where each blade is independently controlled by a servo actuator. But all of the blades respond to the same command as they go through their cycle. Individual pitch blade control provides real-time feedback from blades or monitoring devices, and one approach is to embed sensors into the blades for real time load feedback. The system closes the loop at the turbine level using that feedback to significantly reduce the load variation from blade to blade. The result is an ability to handle peak gusts better and more quickly.
Oh, I get it. I didn't realize you meant not only getting the most out of a particular gust of wind, but keeping them going in the first place, so they are turning whenever there's wind instead of staying idle just because there's wind but not going the right way.
By experimenting with the photovoltaic reaction in solar cells, researchers at MIT have made a breakthrough in energy efficiency that significantly pushes the boundaries of current commercial cells on the market.
In a world that's going green, industrial operations have a problem: Their processes involve materials that are potentially toxic, flammable, corrosive, or reactive. If improperly managed, this can precipitate dangerous health and environmental consequences.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
