I understand what you're saying, Jack, but it doesn't make sense for the company to not fix the problem. We see this over and over again in the Monkey blogs. There's a rule of thumb that a satisfied customer will tell a couple people, while a dissatisfied customer will tell 20. Given the Internet, a dissatisfied customer now may tell thousands.
I agree that the problem might very well be in accounting, although I'm starting to wonder whether or not these really are overlooked as you suggest. What if its a case of playing the odds that X% will fail during the warrenty and only Y% of the owners will actually file a valid claim and at the end of the day, the company comes out ahead. This is sort of like companies that give rebates rather than discounts. They know that people will look at the rebated bottom line when chosing a product, but the actual filers are at a much lower percent.
That's pretty bad, Glenn. You'd think that with a well-run company, there would be some backtracking on the accounting for warranty recall costs to determine their source. Then a circle back to make sure whatever was causing the warranty costs could be corrected on the manufacturing side. Seems that would be a simple function that could save countless thousands of $$.
While I was working at GM there was a recall on bolts securing part of the front wheel suspension. The new bolts were breaking, so the recall was to replace the breaking bolts under warranty.
My theory is that an engineer proposed replacing the bolts with cheaper bolts to save about $1.00 per thousand. Cost reduction is good, so the manufacturing cost of the car was reduced by pennies. This cost savings is applied to the Manufacturing Costs Account.
Then the waranty replacements happen, at a cost of perhaps $50.00 per bolt in recall notices, shipping, dealer labor costs, and whatever. These costs are applied to the Warranty Recall Costs Account.
But no-one looks to see that the penny savings in manufacturing then cost dollars in warranty. There is a difference between making something less-expensive, and making it cheaper. Is it possible the problem with the storm doors a result of cost reduction in manufacturing ?
@William K.: Sometimes, high iron levels in aluminum are a result of re-melting low quality scrap, as you point out. In other cases, iron is intentionally added to aluminum in order to prevent die sticking, without a lot of thought as to its effect on mechanical properties. Excessive iron results in the formation of aluminum-iron-silicon intermetallic compounds, also known as "sludge." Sludge reduces mechanical properties, especially ductility and fatigue strength. It also decreases fluidity, which tends to promote porosity. In short, it's bad stuff.
Thankfully, though, my experience has been that seriously off-spec chemistry is fairly rare, even in castings sourced from China and India. In this case, it sounds like the problem is a design which simply doesn't leave enough material at the edge of the hole.
I think your fix of simply drilling new holes in the door so that it will accomodate another manufacturer's latch is probably the best solution.
There are serious quality problems with some kinds of aluminum castings coming from some areas of China. The main cause is poor quality metal, aluminum with a lot of iron in it, and isteel that includes a lot of "non ferrous" materials. That may be part of the problem.
Unfortunately you have been causght in the nonstandard part trap, and are compelled to continue purchasing the same poorly designed pieces repeatedly. So spend the effort, drill the new holes, and purchase a good quality door latch. That will be the end of those problems.
The secret is to measure carefully and then center punch each hole to be drilled, and to drill a smaller pilot hole first.Also, use a drill lubricant and don't press very hard. That gives fewer burrs to trim off.
That's funny, Uniquity. I have to start trying that. I've found that athletic socks don't last as long as they used to. In the past I got years of wear. Now I'm luck to get four months before the white socks start to pull out of shape of start tearing. I need to demand an extended warrantee.
Since the low quality of many current products as spawned the stores to push extended warranties on almost everything they sell, I have devised my own plan. I do not get the extended warranty they offer, but when I buy items like nuts and bolts, I ask for the extended warranty. It really confuses the clerks when I want the extended warranty on socks. I do not mean to pick on the checkout clerk, but I hope the word will get to management that something is going on.
That's exactly right. When my mother called to order the latest replacement, she asked if it was made in America and the clerk said "Yes, it is." When the box arrived via FedEx a week later, printed on two sides of the box were the words: "Made in China". I guess even Andersen is feeling the cost pressure.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
The 3D printing revolution seems to have a knack for quickly moving technology ahead by way of collaborative effort and even a little friendly competition -- all of course in the name of scientific advancement.
Advantech has launched a new series of motion-control I/O modules to meet the increased demands that come with more distributed industrial systems that require control of a growing number of axes and devices.
Using almost 200 light-emitting diodes in the front and back of the new 2014 CTS, Cadillac designers are showing how LEDs can change the character of a vehicle.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
2 
