Larry, you very well may be right. Yet I would think the problem would be even more widespread, enough for component manufacturers and brand owners to raise a stink about it. Yet none of them are saying much that I can see. The electronics industry seems pretty blasé about the subject these days.
Whether or not you choose to deny it, the tin whiskers problem is real, as are the problems with brittle joints and components stressed by overheating during assembly. Many of the complaints we hear about and read in Design News relating to poor American design or Chinese manufacturing and the short life of electronics including appliances, cameras, cellphones, computers, and MP3 players are due to problems with solder.
I've repaired my son's dryer (brittle solder joints between the relay pins and the circuit board) and the remote control for my DVR (probably tin whiskers, as the problem was resolved by brushing the closely-spaced leads of all surface-mount components with a fine brass "toothbrush." Probably a half-dozen other such repairs too.
I know there are still those out there who says the problem hasn't been solved. At this ploint, that doesn't seem to be a widely held position. Even so, when electronics fail, there is a number of people who yell, "Tin Whiskers." That voice rose up when Toyota was having its accelerator problems.
My RoHS coverage was focused on what was happening on the PCB and how replacing various materials, most obviously lead solder materials, had various effects on production and performance. That coverage slowed down, as apparently yours did, when the problems started getting solved.
I didn't realize you covered RoHS, Ann. I did too. For a couple years before and after the RoHS deadline, I ran a Lead-Free Zone mini-website here at Design News. It was a hot site until the RoHS deadline came and went, at which point I shifted to covering REACH and all the different flavors of RoHS (China, Korea, California). Now it seems to be a fairly quiet subject.
Thanks for the reply. You may well be right. RoHS compliance in electronics is just about 5 or 6 years old now. I began writing about it a couple of years before that. The problems in finding solder replacements that were good enough and didn't require cooking the board at much higher temperatures than tin/lead--thus melting other materials or at least shortening their lifespans, as well as all kinds of differential CTE problems--were legendary. Re the health issues, I'm grateful we don't have lead water pipes out here. One of these days I'll be able to replace all our galvanized steel plumbing with copper.
Sure Ann, I should state first off, I am only talking about an impression. I have not looked at the date of manufacture to accurately place the timeline with general RoHS compliance or to look for any detailed marking on the PWB. I think the module is at least 5 or 6 years old.
I confess I have more 37/63 Pb/Sn solder in various gauges than I will be able to consume in my lifetime. The only nod to lead replacement I have made in my personal life is to replace all the water pipes in our home and use Sb/Sn. Having a ready supply of "the Good Stuff" I repaired the fractured solder joints and retinned all the card edge connections with Pb/Sn.
I am afraid I only have anecdotal evidence and suspicions to cast aspersions on early RoHS compliance failures.. However, overall the solder job on this board I would rank as terrible, even by my amateur standards.
Ken, I'd like to know more about what you mean by the poor solder joints being due to early attempts at RoHS compliance. I can guess--some years ago I wrote in some detail about the problems associated with solder replacements to meet RoHS requirements. Can you elaborate a bit?
Your tale reminds me what else I did. After I re-tinned the card edge connectors I cleaned them with a contact cleaner that, besides removing oxide, leaves a little mineral oil on the surface to reduce contact oxidation.
IF you want to "blame" someone for this short-sighted engineering, blame MOTOROLA! For those of you old enough to remember, MOTOROLA made a big advertising campaign out of their newly designed & configured TV sets & other home entertainment products with the "WORKS in a DRAWER" concept in the late 1950s & 1960s. They incorporated all of the low level circuits onto printed circuit boards. That was a distinct departure from the hand-wired sets of the era.
They advertised that IF a module went bad, the serviceman could come and easily replace the entire module, and you'd be back in businees in no time flat. It was meant as a counter to the common policy that service people would remove your TV or other component to repair it at the "shop". It was cast as a money-saving idea. From there, the floodgates literally opened, since many other companies adopted similar design guidelines, so that EVERYTHING one buys today has become a modular "throw away".
Truchard will be presented the award at the 2014 Golden Mousetrap Awards ceremony during the co-located events Pacific Design & Manufacturing, MD&M West, WestPack, PLASTEC West, Electronics West, ATX West, and AeroCon.
In a bid to boost the viability of lithium-based electric car batteries, a team at Lawrence Berkeley National Laboratory has developed a chemistry that could possibly double an EV’s driving range while cutting its battery cost in half.
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This discussion will examine what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.