Larry, you very well may be right. Yet I would think the problem would be even more widespread, enough for component manufacturers and brand owners to raise a stink about it. Yet none of them are saying much that I can see. The electronics industry seems pretty blasé about the subject these days.
Whether or not you choose to deny it, the tin whiskers problem is real, as are the problems with brittle joints and components stressed by overheating during assembly. Many of the complaints we hear about and read in Design News relating to poor American design or Chinese manufacturing and the short life of electronics including appliances, cameras, cellphones, computers, and MP3 players are due to problems with solder.
I've repaired my son's dryer (brittle solder joints between the relay pins and the circuit board) and the remote control for my DVR (probably tin whiskers, as the problem was resolved by brushing the closely-spaced leads of all surface-mount components with a fine brass "toothbrush." Probably a half-dozen other such repairs too.
I know there are still those out there who says the problem hasn't been solved. At this ploint, that doesn't seem to be a widely held position. Even so, when electronics fail, there is a number of people who yell, "Tin Whiskers." That voice rose up when Toyota was having its accelerator problems.
My RoHS coverage was focused on what was happening on the PCB and how replacing various materials, most obviously lead solder materials, had various effects on production and performance. That coverage slowed down, as apparently yours did, when the problems started getting solved.
I didn't realize you covered RoHS, Ann. I did too. For a couple years before and after the RoHS deadline, I ran a Lead-Free Zone mini-website here at Design News. It was a hot site until the RoHS deadline came and went, at which point I shifted to covering REACH and all the different flavors of RoHS (China, Korea, California). Now it seems to be a fairly quiet subject.
Thanks for the reply. You may well be right. RoHS compliance in electronics is just about 5 or 6 years old now. I began writing about it a couple of years before that. The problems in finding solder replacements that were good enough and didn't require cooking the board at much higher temperatures than tin/lead--thus melting other materials or at least shortening their lifespans, as well as all kinds of differential CTE problems--were legendary. Re the health issues, I'm grateful we don't have lead water pipes out here. One of these days I'll be able to replace all our galvanized steel plumbing with copper.
Sure Ann, I should state first off, I am only talking about an impression. I have not looked at the date of manufacture to accurately place the timeline with general RoHS compliance or to look for any detailed marking on the PWB. I think the module is at least 5 or 6 years old.
I confess I have more 37/63 Pb/Sn solder in various gauges than I will be able to consume in my lifetime. The only nod to lead replacement I have made in my personal life is to replace all the water pipes in our home and use Sb/Sn. Having a ready supply of "the Good Stuff" I repaired the fractured solder joints and retinned all the card edge connections with Pb/Sn.
I am afraid I only have anecdotal evidence and suspicions to cast aspersions on early RoHS compliance failures.. However, overall the solder job on this board I would rank as terrible, even by my amateur standards.
Ken, I'd like to know more about what you mean by the poor solder joints being due to early attempts at RoHS compliance. I can guess--some years ago I wrote in some detail about the problems associated with solder replacements to meet RoHS requirements. Can you elaborate a bit?
Your tale reminds me what else I did. After I re-tinned the card edge connectors I cleaned them with a contact cleaner that, besides removing oxide, leaves a little mineral oil on the surface to reduce contact oxidation.
IF you want to "blame" someone for this short-sighted engineering, blame MOTOROLA! For those of you old enough to remember, MOTOROLA made a big advertising campaign out of their newly designed & configured TV sets & other home entertainment products with the "WORKS in a DRAWER" concept in the late 1950s & 1960s. They incorporated all of the low level circuits onto printed circuit boards. That was a distinct departure from the hand-wired sets of the era.
They advertised that IF a module went bad, the serviceman could come and easily replace the entire module, and you'd be back in businees in no time flat. It was meant as a counter to the common policy that service people would remove your TV or other component to repair it at the "shop". It was cast as a money-saving idea. From there, the floodgates literally opened, since many other companies adopted similar design guidelines, so that EVERYTHING one buys today has become a modular "throw away".
By experimenting with the photovoltaic reaction in solar cells, researchers at MIT have made a breakthrough in energy efficiency that significantly pushes the boundaries of current commercial cells on the market.
In a world that's going green, industrial operations have a problem: Their processes involve materials that are potentially toxic, flammable, corrosive, or reactive. If improperly managed, this can precipitate dangerous health and environmental consequences.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
