I like your way of thinking, Naperlou. Combining all of those disparate, but related 3D technologies can certainly play a huge role in helping manufacturers address quality issues in an expedient, cost-effective, and continuous manner. Armed with that kind of real-time ability to respond and improve, perhaps American manufacturing can move forward in a positive way as Alex's comments suggest.
Thanks, Chuck. I'm sure the processing requirements are high but multi-core processors are perfect for this type of application. As Moore's Law marches on in automation controllers, vision is definitely one of the apps that should be able to expand by using the extra available processing horsepower.
I think wider adoption will still be slow, Al. The wild card, however, might be the economy. If auto sales jump, we could see wider adoption of 3D for a lot of different automotive applications, such as inspection of braking components, fuel lines and tire treads.
There's a convrgence of trends that are making 3D more viable, Rob. Availability of software libraries has been important, but equally important is the availability of multicore processors to run the applications. We're hearing of users who are employing 8, 10, and even 12 cores to do the processing. 3D is also getting a bit simpler. In-house engineer without 3D experience can do simple applications, such as de-palletizing. And now there are more system integrators who can handle robotics applications. It's still complex, but 3D no longer requires the expertise of Ph.D.-level specialists.
Nice article, Chuck. I look forward to the next one.
What was the tipping point on the adoption of 3D vision. Was it the cost of cameras coming down? Was it software developments that made it easier to deploy (i.e. users don't have to do complex original programming)? Or something else?
One question for 3D vision in automation applications is how much this technology expands the processing requirements required for these more sophisticated vision applications. With the move toward one controller, one network and PC-based systems where users are gaining confidence in the reliability of the real-time operating systems, a sharp increase in processing for 3D would potentially inhibit adoption at some level. Chuck, any ideas on the impact this might have from your research?
Chuck, thanks for a clear, comprehensive article on this subject. I think Alex's point is well taken: that the increase in the use of 3D techniques in MV are all about quality control, and good evidence for the revival of US manufacturing skills, ability and quality. Beth's and naperlou's comments are also intriguing: the implications of such convergence could be mind boggling.
Beth, I think you are right on with your comment. We are now moving into a design world where 3D design, printing and machine vision could streamline design and manufacturing and flow between them. Just imagine the possibilities for continuous improvement when you can combine the three.
This is the cover story in the February print issue of Design News. My comment would be, the increased quality control enabled by wider deployment of 3D vision plays into the whole meme of the resurgence of U.S. manufacturing. Not that this technology won't be used worldwide -- it will. But its deployment Stateside, particularly in the resurgent domestic automotive industry, will go a long way towards keeping U.S. manufacturing on par with its tough worldwide competition.
Chuck, Excellent article. This should be a very interesting area for automation and control over the next decade. As computing platforms and operating systems continue to move to the next level, vision should be an area ripe for innovation. Any ideas about how quickly we'll start to see wider adoption?
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
7 
