Good catch, but I'd be very concerned about why a cable shield that is supposedly grounded at one end has enough AC on it to give a nasty shock. You have to wonder about the technical prowess of those who initially designed/installed/tested the system.
Years back I was fighting a problem with the waveshape from a T1 interface. It turned out the whover wired that telephone central office used 72 ohm twisted pair instead of the proper 100 ohm cable.
OMG how could it possible in such ammount, I mean as per Government the labour cost may exceede $10. Looking forward for this desiogn, hope governement should approve this and apply everywhere.
I am amazed that anybody would use BNC connectors for an audio input on a remoted transmitter. My guess is that the transmitters were not designed to be remoted like that. Transformer coupling, balanced or not, with an electrostatic shield between primary and secondary, was definitely the correct fix.
OF course, it would have been valuable to figure out why there was 90 volts AC between the two grounds. I can immagine several explanations, though.
And of course there is always the burden of believing that the system functioned correctly at some time. Unfortunately, not everything that is built is designed, and not everything that is designed is designed correctly. So sometimes there are problems like this.
Yes, it was definately a band-aid moment. The solution would have been to redesign the audio output and input stages of the communications gear to use isolated and balanced audio at both ends. The equipment rack and consoles were separated by 6 floors. I admit that the AC Safety ground for the building wasn't up to the challenge, or that there was some other piece of equipment that at causing the problem of a high difference in the ground potential.
But all of that aside, the real problem was a crap design using unbalanced audio extended over several floors which would have caused problems no matter what. The equipment manufacturer, C----ns, should have known much better.
The isolation transformers where mounted on a piece of plexiglas and had a cover and warnings on it identifying the problem. This didn't exist prior to the band-aid moment.
I would have thought that over the 15 year period that this problem existed that someone would have corrected the problem on such a critical service much earlier.
The transformer is a bandaid. However I have been in several situations where it was impractical or not cost effective (or permitted) to fix the 'real' problem.
I have often thought about how much the government would have spent over the 15 years that they tried to resolve this problem. Of course, I was never told, but I did catch heck for being $5.00 over what I had estimated the repair cost would be! It's been 35 years since I have worked there. I wished I did know...
I'd been playing with electronics since I was a child, and at this point, troubleshooting had become almost instinctive. What had amased me at the time was that no one realised where the problem lay! It was pretty obvious where the problem was coming from.
One thing that I have noticed is that when trouble shooting equipment, people tend to think that the installation was working at some point. If everything that was checked is as it should be, it's usually the thing that no one has checked that's causing the problem!
Whatever earlier solutions were tried, they had to cost more than $105 in labor alone. What it comes down to is that it's really hard to replace a smart enginer.
Yes, Naperlou, the trick for Clint's success may have been that he didn't know what was attempted earlier. Like you, I'd like to know what that was. Clint will be checking in on these comments, so we may get the rest of the story.
Clint, what a great story. You took a disciplined approach without preconceptions. You questioned the selection of the cable and tracked down the issue. I just wonder what was done before to address the issue. Sometimes it pays to take a new approach without knowing what was done before.
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
6 
