What an interesting display. I like the steel wool idea. Yet another example of the power that resides in a 9V battery. I guess the magic of the 9V is that the terminals are so close together.
Having taught Map/Compass & Survival for over 15 years...the 9V battery and steel wool demo is one that always wakes up the sleepers in the students. I always show this trick to my classes. The finer steel wool works best, as you are causing a short circuit via the steel wool, and the higher the resistance the better...ie. fewer, thinner strands of steel wool. STeel burns, of course, which is how it is cut...get it hot and supply O2. so, touch a few strands of the steel wool to the 9v battery terminals, and when it glows, blow on it. Be sure to have it where you an drop it safely...as you will SOON.
I grew up in the carbon zinc era where batteries had suffciently high internal resistance and low current capability not to be much of a fire threat. I had to adapt to the new cell chemistry that could be quite dangerous if mistreated. As for 9V transistor radio batteries, they too started off as carbon zinc piles and only later on became alkaline power houses.
About the only batteries with any clout in the carbon zinc days were the very large and heavy ignition batteries that looked like extremely overgrown D cells on steroids but with screw terminals on top. We'd use a couple of those or maybe a hotshot battery, another oversize carbon zinc style, for starting model airplane engines (to heat the glow plugs). To get an idea of the size, picture a cylindrical D cell battery the size of an 18 ounce beverage bottle.
While a 9 VDC battery isn't much of a biological hazard, especially when routing electrons through your tongue, the risk of death only occurs if suffcient current can flow across your chest cavity inhibiting normal heart electrical activity. It only takes around 100 milliamperes to block the heart from beating. More dangerous is 60 Hz AC as it'll induce fibrillation, the heart fluttering rather than pumping.
Back to the good old days of carbon zinc, the only batteries that could deliver sufficent current through your skin resistance to maybe stop your heart were the B batteries for portable vacuum tube radios. Yes, radios at one time used these odd glass tubes filled with nothing to act as amplifiers and diodes. But to get electrons to traverse the nothingness required significant voltage. B batteries might have contained a suffcient number of cells stacked in series to produce over 90 VDC per battery. Put two or three in series and you got plate voltages in the range of 180 to 270 VDC. Ouch!
About the only household electronic appliance these days with vacuum tube technology is the microwave oven. Do not play with its innards if all you know about are IC's and transistors! The magnetron tube has a lethal high voltage power supply to make it do its power RF oscillation at 2.4 gigahertz.
Yes, I've spent a whole lifetime with masking tape over the 9v batteries in the junk drawer. It was always just something you do when you put a 9v away, like licking the ends before poping them into a toy robot or train.
Tim is certainly correct about the fire starting kit used by some scouts. Fine steel wool and even a weak battery would be good for a few lights. The trick was to pack the battery in a plastic baggy with the dry tinder, and have the steel wool in a different plastic baggy. As with most fire-starting mixes, the ingredients must be kept apart until time to start the fire. As far as I can tell, though, it is not an officially sanctioned method of starting a campfire.
I have wondered about doing that same thing but using a 120 volt cord and a lot more steel wool, but I have not experimented with it. It might approach the "exploding bridgewire" method used in many military systems, but it would probably be less predictable.
I have not done that with a battery in the pocket, because I read about somebody else doing it and I decided to avoid that problem by putting masking tape over the battery terminals. That took care of that.
But I had a dumb co-worker who put about fifty dollars worth of coin cells in a drawer with nothing to prevent short circuits, and who was offended when I was critical of doing something that ruined all of those batteries. They were not the rechargable ones, they were the expensive long life ones. MY assertion was that it was much smarter to leave them in the original packing material until time to install them. His STUPID defense was that it was not as neat.
I grew up doing it all the time. The 9v battery was the standard for transistor radios. They were portable, they were filled with Beatle music, and they ran through batteries quickly. So it was a regular activity, licking the batteries bumping around in the junk drawer to see which of the weak batteries still has some juice.
I've done that a time or two. But it's probably not the best way to test a battery. I don't know of any side effects. But better to be safe than sorry. I don't know of any side effects....side effects...side effects... But better to be safe than sorry. Kids don't try it at home.
Okay, that sounds a little too much like Mcgyver, but I will admit that I will be using this trick the next time I'm outside playing in the snow and want to warm up a little bit. Thanks for the idea.
As a kid, I had read about a fire starter kit comprising of a 9V and steel wool that you can use to start a fire for a campout. Being a good Cub Scout, I decided to put a battery and some steel wool in my Dad's bag for our upcoming campout. Fortunately for us, the bag caught fire outside of our house and did not require the fire department. I obviously missed that you must put the steel wool in a baggy before storing by the battery.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
The 3D printing revolution seems to have a knack for quickly moving technology ahead by way of collaborative effort and even a little friendly competition -- all of course in the name of scientific advancement.
Advantech has launched a new series of motion-control I/O modules to meet the increased demands that come with more distributed industrial systems that require control of a growing number of axes and devices.
Using almost 200 light-emitting diodes in the front and back of the new 2014 CTS, Cadillac designers are showing how LEDs can change the character of a vehicle.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
