Chuck, someone knows a lot about the subject, and I wish I did. I've already spent quite a lot of time surfing and snooping around on the Web, but it's quite difficult to find out anything aside from what's in that GAO report, and Boeing is less than forthcoming. I assume this is for security and/or market competition reasons. I'm checking the MRO schools' websites for course descriptions, e.g., but not much luck so far. The thing to remember, in general, is that repair techniques have existed as long as composites in aircraft have existed, but for some time it was all military. Then they entered the commercial aircraft sector, but not, I repeat not, in primary structures. Their use in primary structures has changed everything.
Alex, thanks for thinking industry-wide again. I agree, the technology is certainly in the early stages and it makes me wonder how many other coatings manufacturers or composite airstructure makers are conducting similar research under the radar, possibly even in partnership with each other. It might make more sense from an industry standpoint to develop and commercialize something that can be applied by all airstructure manufacturers and regulated by the FAA. But that also assumes that it can be applied in an aftermarket scenario and still work properly. I get the impression that GKN's coating needs to be "baked" in, either literally or figuratively, in order to do its job. But that could also be because they are not a coatings manufacturer.
TJ, that's funny, using whiteout to detect cracks and delams. I bet it worked great. But I doubt if that would work on CFR composites or even glass-reinforced composites. Damage on these, especially CFR, is invisible to the naked eye and techniques for detecting it different from those used for detecting same in traditional materials. You are right, I carefully did not reveal the wavelength since I honored the company's request in order to get this much published.
You say damage-detecting coatings have been around for awhile, but not using non-visible wavelengths. Do you mean that damage-detecting coatings *for these composites* have been around for awhile? Please inform us if you know!
Thanks for the info, Ann. So that means that the ability to utilize this detection technique will be proprietary, but I guess it also indicates that the state of the technology is at the point where other composite makers should be able to do this too, at least eventually. (That's unless there's only a very narrow class of coatings which are amenable to the detection process, and they're patented or trade secret.) Anyway, I guess the upshot is that this is not going to be anywhere near as industry-widee as I assume. At the same time, it opens up the idea that, with technology advancing, maybe the FAA can move towards some specificity in its composites directives.
I've seen simple things like White-Out used during materials testing to detect cracks and delaminations.
The damage-detecting coatings themselves I believe have been around for a while. The trick to which this article alludes is the non-visible wavelengths that would be used. THAT is a good idea. Damage-detecting coatings that the flying public can see are not confidence building.
The article carefully did not state which spectrums would be used, whether infrared or ultraviolet. I might consider watching the wing with my IR scanner in the future....
Alex brings up two important points. First, since this proposed coating or class of coatings will be available only as an inherent part of a composite airframe structure sold by one company, it won't be available for other composite airframe structures sold by other manufacturers. I've already heard of one other project targeting a similar purpose but using an entirely different chemical and behavioral model. That means competition among different types that work in different ways. So actually there may not be much in the way of industry-wide techniques.
Second, it does provide a great opportunity to gather MBTF data. Even if it's coming from airstructures using entirely different coating types, the data should be comparable about how composites break.
This is indeed a significant development because it holds the promise that there will be a cost-effective, easily implementable, repeatable, industry wide technique for inspect composites. This is going to be critical important not only to prevent in-flight failures, but also to gather life (MTBF) data on how different composite structures actually perform on commercial aircraft, particularly on primary structures like wings. (A primary structure in aerospace terms refers to a part where, if it fails, the plane will no longer be flyable. So for example you can survive a rip in the fuselage, but not the loss of a wing.)
I don't think the technology has been around for awhile, at least not for composites. The idea may have been. But there's a big difference between realizing one can use coatings to assist in detecting damage--the no-brainer aspect--on one hand, and on the other figuring out exactly what coatings, how they should work, how to apply them without causing other problems, etc. Since GKN is a supplier of composite airstructures and since their scientist describes redesigning a coating at the microsphere level, I would suspect that what's taken some time is the process of figuring out details of how to make and implement such a coating. Even at this point before the 18 months + another 18-24 months before commercialization, they gave a quite coherent description of the basic idea. Yet it will likely take 3+ years before a flight test is likely. So the R&D involved is not trivial.
The 3D printing revolution seems to have a knack for quickly moving technology ahead by way of collaborative effort and even a little friendly competition -- all of course in the name of scientific advancement.
Advantech has launched a new series of motion-control I/O modules to meet the increased demands that come with more distributed industrial systems that require control of a growing number of axes and devices.
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is