Dave, You just articulated the point that I was trying to make so much better than I did. It does seem like a no-brainer, especially if the technology has been around for a while. I'm wondering what hurdles there were preventing this from being put to use in any significant form prior to now. Or maybe it's that there wasn't a formal market for something like this given that composite materials are just now becoming so dominant in aerospace design.
Thanks, William and Dave, for sharing your experience in this area. It surprises me that using composites as a repair material for aluminum didn't strike anyone as not a good idea, since their properties are so different. To my limited knowledge so far, repair materials for composites are supposed to pretty closely match the material they are replacing.
The whole subject of using coatings to monitor structural health does seem obvious, doesn't it? I notice that Stresscoat does not appear to address composites. The big deal about them is the fact that damage can be invisible, hence the attempts to make it visible under other wavelengths. And yes, you would think that research such as GKN's would have already occurred, and perhaps it has. Theirs was not easy to find, so it's possible there's other such research going on quietly.
Beth, I understand that designing these different coatings is equally simple, whether one coating detects one energy level or multiple energy levels. Creating the actual coating may be a different story, but that wasn't entirely clear. In any case, GKN said it plans to sell the coatings as an integral part of its composite aircraft structural components, not as a separate product line.
Coatings such as Stresscoat have been used in experimental stress analysis for decades. It seems like a no-brainer to use something like this for structural health monitoring. Of course, it's easy to say that something is a no-brainer after someone else has already come up with it. I'm just surprised that nobody came up with something like this sooner.
Thanks for the article Ann! It is great to see this technology being commercialized and incorporated into engineering materials. I was involved in the development of diagnostic coatings which, when excited and viewed under specific wavelengths, provided surface information of temperature, pressure, strain, and cracks. The coatings were applied to the surface of the completed unit for testing. I'm delighted to learn of continued development of both surface and internal coatings during component manufacturing.
One of our biggest surprises came from using composite repair material when applied to traditional metals (aircraft aluminium). Our coatings were used to inspect the performance of a "composite Band-Aid" that could be used to field dress a fatigue crack until the panel could be replaced. The difficulty was that the mechanical performance of the composite material was so superior to the original alloy that the repair site was often a greater point of additional fatigue cracking in the original metal because of the sharp differences between the materials. I imagine things will be better and far superior when all of the components are made out of advanced composites in the first place.
Very cool piece of development and one that would certainly benefit broader use of composites. The idea that a coating could deliver intelligent inspection capabilities is in some ways out there, but then again, in keeping with steady pace of technological advances. In many ways, the development strategy makes perfect sense. Do you have a sense of how difficult or how unique it is to develop a single coating with different signatures that can appear different depending on different energy levels of impact?
For 3D printing to make the jump from rapid prototyping to manufacturing, engineers will need to find easier ways to move products from their CAD screens to their printers.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
New versions of BASF's Ecovio line are both compostable and designed for either injection molding or thermoforming. These combinations are becoming more common for the single-use bioplastics used in food service and food packaging applications, but are still not widely available.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
1 
