HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Comments
View Comments: Newest First|Oldest First|Threaded View
<<  <  Page 6/6
naperlou
User Rank
Blogger
Re: Never a problem with USB connectors
naperlou   1/19/2012 5:00:14 PM
NO RATINGS
Well, Beth, I think you are lucky.  I have seen problems with these connectors.  Some just stop working.  Others seem to degrade.  I get messages that the device can go faster if plugged into a USB 2.0 port (when that has been how it worked all along).  I plug it into a different USB port and it works full speed. 

Ann R. Thryft
User Rank
Blogger
Re: Never a problem with USB connectors
Ann R. Thryft   1/19/2012 1:29:46 PM
NO RATINGS

I'll add my 2 cents to the clamor and say I've never had a problem with USB connectors. The fact that the author says it's the female end, inside the device, which tends to break makes this a major problem, since it's relatively inaccessible.

I was puzzled by the author saying there's no indication on the male plug regarding which side is up. Uh, you must have a Windows machine. Macs have always indicated which end of the plug is up with a symbol.


Rob Spiegel
User Rank
Blogger
Re: Never a problem with USB connectors
Rob Spiegel   1/19/2012 1:20:21 PM
NO RATINGS
I agree with the upside-down problem, Jenn. In the posting, the user said you're going to hit it wrong about 50 percent of the time. I have a side-loading input in my laptop, so 50 percent misses are about right. Yet those misses don't seem to do any damage to either the USB-A connector or the laptop port.

Jennifer Campbell
User Rank
Gold
Re: Never a problem with USB connectors
Jennifer Campbell   1/19/2012 10:39:54 AM
NO RATINGS
I've also never had a problem with USB connectors breaking, nor have I heard complaints from friends or co-workers regarding this issue. I wonder if this is a common problem for many or if there is some sort of wacky user error going on in the case of this author. In any event, the only problem I ever have is when I try to jam the connector into the slot, only to realize I have it upside down.

Rob Spiegel
User Rank
Blogger
Re: Never a problem with USB connectors
Rob Spiegel   1/19/2012 10:16:17 AM
NO RATINGS
I've never had a problem with a USB-A either, Beth. Though I've always felt uncomfortable with the leverage factor. The way the thin USB-A sticks out of a laptop makes me think that dropping the laptop just a few inches at the right angle would snap the USB right off. So far, I've been careful not to drop my laptops.

antedeluvian
User Rank
Iron
USB-B
antedeluvian   1/19/2012 8:57:16 AM
NO RATINGS
I have never had a problem with USB-A, but I have had a USB-B detach from a printed circuit board (part of the microcompuiter in-circuit emultaor) when I was trying to debug a product 500 miles from the office. In order to continue working I had to cut the USB cable and solder it directly to the PCB.

The problem was that there was no mechanical reinforment of the connector which is mechanically held on by the surface mount solder connections only.

Beth Stackpole
User Rank
Blogger
Never a problem with USB connectors
Beth Stackpole   1/19/2012 7:22:34 AM
NO RATINGS
I read this post with great interest waiting for the "aha" moment when I too could say, I experienced that as well. I have to say with all of the devices/laptops/desktops scattered around my house/home office, I have never, ever had a problem with a frail USB connector, despite the numbers of times I've connected/disconnected. I'm wondering if the USB connector is from a specific manufacturer or set of manufacturers and perhaps quality issues belies the problem rather than the actual USB-A connector standard.

<<  <  Page 6/6


Partner Zone
Latest Analysis
The popularity of Pokemon Go may be break open a new rush of augmented reality products.
Engineers in Australia have discovered a mechanism that could allow for the design of new composite materials for light harvesting and optoelectronics.
Here's a blast from the Gadget Freak past. Check out these gadgets, from telescope warming to keyboards on your fingers
A new method of modeling how they are created with chemical vapor deposition (CVD) could reduce the cost of carbon nanostructures used for for research and commercial applications, including advanced sensors and batteries.
BMW has already incorporated more than 10,000 3D-printed parts in the Rolls-Royce Phantom and intends to expand the use of 3D printing in its cars even more in the future. Meanwhile, Daimler has started using additive manufacturing for producing spare parts in Mercedes-Benz Trucks.
More:Blogs|News
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jul 11 - 15, Embedded System Design Techniques™ - Debugging Real-time Embedded Software – Hands on
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9 | 10


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Technology Marketplace

Copyright © 2016 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service