One might comment about your own illiteracy. You might consider checking dictionary.com . That site will permit you to cite a word correctly and not appear short-sighted.
So, you are saying the power supply wasn't properly grounded and the output was float in reference to ground. Sounds like things were not properly installed and grounded. I don't go along with the Vandergraf garbage,
I agree, Rob. It's amazing that problems like this one ever get solved. This isn't just a glitch; it's a sub-system glitch, made even tougher to find because firmware was supposed to be the culprit.
You're lucky you were able to isolate it. I've seen many intermittent failures in the lab, which were impossible to reliability repeat, and thus diagnose. I suspect this is something that's very widespread, and accounts for a lot of in-the-field glitches.
Actually, the grounding precautions were not so much for the equipment, but for the safety of the developing prototypes and new product introductions.But the equipment is normally sitting right on the same bench as the product, which is the target of the precautionary measures. And yes, this was a recent practice used on manufacturing floors as late as last year when I was introducing a military computing device at a domestic OEM.
Wow, Jim. Is that type of restriction common these days? I would imagine there are ways to ground equipment that doesn't require personnel to wear such elaborate gear.
Boy does this bring back memories of grad school. We had an ultrafast-spectroscopy instrument that we assembled from $1.2 Million of lasers and fancy electronics equipment. In essence, our system was a very, very fast strobe light that would illuminate a repetitive chemical reaction at precisely the right time. We used a liquid nitrogen-cooled scientific CCD camera that would record the faint output signal viewed through a maze of optics and filters. We would darken the lab and use upwards of 20-min CCD exposures to collect the very faint signal. Every now and again our data would be extremely noisy and we would have to collect data again. After some major sleuthing, we discovered that one of the PCs on the far side of the lab running Windows3.0 had a screen saver consisting of a bouncing ball. All but the top 5% of the computer monitor was obscured by equipment and only when the image of the ball bounced near the top of the screen did the extra photons get entrained into our optics. I've disliked screen savers ever since...
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
7 
