HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Comments
View Comments: Newest First|Oldest First|Threaded View
<<  <  Page 3/3
William K.
User Rank
Platinum
The powerless pump
William K.   12/17/2011 8:19:48 AM
Actually, the pump being driven by flow was my initial guess. Of course, I have a bit of experience with controls for pumping systems.

I had an interesting diagnostics challenge a while back that involved a large pump driven by a large motor. It was in a hydraulic power unit that we had loaned a customer while we were repairing their failed power unit.

The complaint was simple: the pump will not start. Because the customer was an hours drive away, I first asked a few questions, then asked them to have their electricial check the 3 100 amp fuses in the 480 volt power feed circuit. He reported that one 100 amp fuse had failed, I suggested that he replace it and try starting the system again, He replaced the fuse and the replacement fuse failed as soon as they tried to start the motor. So now I had to head over to the customers site and find the problem. My approach was first to do a complete inspection, since that sort of short circuit shaould provide some evidence of itself. But all of the visible wiring looked good. Next, I did a resistance check at the motor terminals of the starter-overload assembly, which showed an open circuit in one phase. That was a good clue. I opened the connection box on the side of the motor and found that, because it had been assembled with the splice pressing against the cover of the box, the one connection had slowly cold-flow, penetrated the tape wrapping and contacted the box cover, short circuiting the phase to ground and evaporating part of the connection. The repair was simple, which was to cut off the damaged end, install a split-bolt splice instead of the lug and bolt splice, and tape the new connection. Then I was careful to position the wires in the splice box so that they did not press against the cover, and replaced the cover. After installing a new 100 Amp fuse, the systm started and ran correctly.

Note that I did switch off the service to the system before I started working on it.

Rob Spiegel
User Rank
Blogger
Re: Weird
Rob Spiegel   12/16/2011 5:24:38 PM
NO RATINGS

I agree, Chuck. That's what makes these Sherlock so much fun. And it's always the super simple answer that wins -- like the magnet that isn’t magnetized or the resistor what was marked incorrectly.


Charles Murray
User Rank
Blogger
Weird
Charles Murray   12/16/2011 5:21:27 PM
NO RATINGS
My first reaction would have been that the breaker had gone haywire. Pump running backwards? It woudn't have crossed my mind.

Rob Spiegel
User Rank
Blogger
Re: Looks can be deceiving
Rob Spiegel   12/16/2011 5:14:46 PM
NO RATINGS
Yes, good observation, Tim. Jennifer is right about how these Sherlock postings show some excellent deductive logic. It's not named "Sherlock" for nothing. What I find most impressive is that many of the solutions arise when the Sherlock involved refuses to make any assumptions.

Noswad
User Rank
Gold
Re: Looks can be deceiving
Noswad   12/16/2011 4:16:57 PM
NO RATINGS
Elementary my dear Watson.

Jennifer Campbell
User Rank
Gold
Re: Looks can be deceiving
Jennifer Campbell   12/16/2011 2:54:47 PM
NO RATINGS
That's good advice Tim, and is generally the case on many of our Sherlock Ohms stories.

Tim
User Rank
Platinum
Looks can be deceiving
Tim   12/16/2011 6:29:20 AM
NO RATINGS
Good job double checking something that your eyes and ears were telling you.  Sometimes it is good to take a step back and ask if what you are seeing is the whole situation.

<<  <  Page 3/3


Partner Zone
Latest Analysis
We shared our list, now Design News readers tell us which artificial intelligence movies they watch again and again.
Researchers have been working on a number of alternative chemistries to lithium-ion for next-gen batteries, silicon-air among them. However, while the technology has been viewed as promising and cost-effective, to date researchers haven’t managed to develop a battery of this chemistry with a viable running time -- until now.
Norway-based additive manufacturing company Norsk Titanium is building what it says is the first industrial-scale 3D printing plant in the world for making aerospace-grade metal components. The New York state plant will produce 400 metric tons each year of aerospace-grade, structural titanium parts.
Researchers have simplified the fabrication of the geometric requirements for fluid motion in microrobots for in vivo medical applications.
The National Aeronautics and Space Administration’s recently announced plan to put an electric airplane in the air by 2018 is forward-looking, but hardly unique.
More:Blogs|News
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jul 11 - 15, Embedded System Design Techniques™ - Debugging Real-time Embedded Software – Hands on
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9 | 10


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Technology Marketplace

Copyright © 2016 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service