Nice to see Mentor building bridges to expand the applicability of CFD software. This kind of thermal analysis has to be critical in terms of optimizing the use LEDs in designs and the ability to predict heat transfer on a subsystem level can only serve to create more efficient and higher quality products.
Fantastic synthesis of Theory and Experiment. This interplay between experimentalists and theorists is just what is needed to get an accurate snapshot of the actual system. The theoretical modeling provided by CFD brings us very close to visualizing the system under study, but only when actual measurements are used to carefully calibrate and verify the CFD models. Calculating overall system performance using component values measured in isolation runs counter to the systems reality that the integrated system is often greater than the sum of the parts. Especially when it comes to energy efficiency, I hope we continue to see more stories like this one.
This is a good example of two interesting trends. One is the use of multiphysics in engineering analysis. The other is the trend toward smart sensors. As mentioned, thermal issues are a major cause of failure in LEDs and large scale integrated curcuits. This is something the EE did not have to spend a lot of time dealing with in the past. It is good to see Mentor Graphics addressing the issue and taking advantage of new sensor capabilities. It makes life easier for all of us.
Cost savings has driven the change to LED lighting; they use less electricity and while expensive on the initial purchase will last much, much longer than conventional lights.
I'm in North Charleston, SC commissioning several projects. North Charleston uses LED traffic signals. Almost every single red and green LED array in the city has at least five LEDs that don't function. In some cases, more than 75% of the LEDs do not turn on. While LEDs do eliminate the single-point failure of incandescent bulbs, 75% failure is unacceptable.
I don't know if it's thermal problems of the LEDs or their circuit boards, environmental aspects of high heat and humidity of this region, or something else. but driving around North Charleston makes me think LED lighting still has bugs to stomped out.
Call me obsessive, but I’ve always thought an LED should last longer than a human if treated correctly.A continuous light at 80K hours is around 9 years.If we kept the junction under 80C or some other less severe level, could we get a lifetime (>100 years) from them?Could they not be “the light that just does not burn out”?
That's a very surprising statistic, TJ. At the rate of 75 percent, I would think the city would reconsider either its supplier or the use of LEDs period. Given the difficulty of fixing and replacing traffic lights, I would imagine a more reliable source -- even if more expensive -- would pay for itself.
The alterantives to consider for the heavy LED failure rate in the traffic light failure is that teh LEDs themselves may not have been quality LEDs from a reputable supplier. There are a considerable amount of low quality LEDs that do not perform as well as the more expensive offerings. Also, it may be the substrate that they are mounted on, the solder joint and several other failure modes. I worked in the automive industry on LED headlights and tail lights. I am sure you have noticed the dead LEDs in the tail lights of the truck ahead of you. The quality and durability of these LEDs and the assembly as a whole where not very good. They have improved and so will the LEDs and sub-assemblies in the street lights. Unfortunately early adopters are the guinea pigs for QC.
Interesting point about some LEDs being better than others in terms of quality. I suppose that's true with any component. Any rough guidelines engineers need to consider to help them spec the proper LED supplier?
Using almost 200 light-emitting diodes in the front and back of the new 2014 CTS, Cadillac designers are showing how LEDs can change the character of a vehicle.
We looked at a number of sources to determine this year's greenest cars, from KBB to automotive trade magazines to environmental organizations. These 14 cars emerged as being great at either stretching fuel or reducing carbon footprint.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
4 
