TJ, your points are well taken. The biggest problem of all in composite repair, though, compared to metal repair, is the lack of knowledge to identify damage in the first place, since it's much more difficult to detect. The next biggest problem is figuring out how to repair so many different materials with so many different uses and so many different possible procedures. And, by extension, lack of knowledge there, as well.
While repairs require more effort, composites would seem to be more damage resistant than an aluminum structure.
I looked for a video I'd seen several years ago: Boeing demonstrating a large skin section held vertically, and airline executives offered the chance to whack it with a sledge hammer.
I cannot find that video so this one will have to do:
Bombardier may go for traditional repair techniques on the areas in danger of ground support damage, but if composites shrug off the damage that would ding aluminum, then composites would seem to be the better bet.
Follow-up from last night's comment: After I mentioned the American Airlines flight that crashed in 1979 after a design flaw left it vulnerable to maintenance damage, I tried to remember where I had once read about that accident. Here's the answer: Our distinguished columnist, Henry Petroski, wrote about it in his book, "To Engineer Is Human."
Thanks, Alex. The news just keeps coming out on this subject. Regarding standards, that's a really good question. One of the key critiques in the GAO report was the point that you can't base repair standards and best practices for composites on the same ones that were created for metal. There are too many differences across the board, and making the same assumptions or using the same templates would be ineffective and dangerous. That may be another reason why we're not hearing much yet about the details of repair whens and hows. I suspect it's a WIP.
@Charles: You're absolutely right; materials selection involves many considerations besides the material's response to stress and strain -- which can be complicated enough, since the material may respond very differently at different temperatures and strain rates, and its properties may be different in different directions. But how a given material will perform in your application also depends on its location in the galvanic series, among other things. Cost and manufacturability are always major concerns, too. Then there are externalities such as recyclability and end-of-life issues, sustainability and lifecycle emissions, etc. And -- although I may be somewhat biased in this regard! -- this is why having a good materials engineer is a necessity.
This is a classic example of the need to beware that what looks good on paper may not always be so. As design engineers, we are often trained to consider matters of stress and strain -- bending, shear, torsional capacity, etc. But here we have a situation where the composite is apparently appropriate in matters of material strength, but not in matters of maintenance. Obviously, maintenance is a huge consideration for aircraft. In 1979, an American Airlines flight leaving Chicago O'Hare crashed, killing 271 people, after a design flaw left the engine pylon vulnerable to maintenance damage.
I'm impressed by the breadth of your recent coverage on composites, Ann. I'm wondering if you see new standards emerging out of the FAA as regards composites repair, or will we see industry-standard practices come into play first, which will become de facto methodologies for both repair and recycling?
Rob, that's the $64,000 question. I think the answer here is also 'both." Composites are definitely moving forward in aerospace, as shown by all the aircraft makers using them in greater amounts. And detection of at least certain types of damage is difficult, but apparently not impossible.
I think the answer is a bit of both. Beth, the industry apparently has been working on solving this problem along with the FAA. At least, that's what they all tell us. But it's quite difficult to find out any details. And that's where ScotCan's point comes in. As the report delineates, industry has been extremely secretive regarding the details about their materials--the type of details which must be well known for determining when and how to repair--in the name of trade secrets.
I'm curious as to whether this is a transition time for composite materials or whether there is something intrinsic to composites that makes detection of problems and repair more difficult for composites than it is for more conventional materials.
For 3D printing to make the jump from rapid prototyping to manufacturing, engineers will need to find easier ways to move products from their CAD screens to their printers.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
New versions of BASF's Ecovio line are both compostable and designed for either injection molding or thermoforming. These combinations are becoming more common for the single-use bioplastics used in food service and food packaging applications, but are still not widely available.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
2 
