You can find stress-strain curves for the previous generation of Ultramid CR here. They compare a 30% glass filled Ultramid CR grade to a regular 30% glass filled Ultramid nylon 6. What I like about these curves is that instead of just giving you one curve per material, they actually give you four: two different strain rates (slow and fast) and two different orientations (parallel and perpendicular to the fiber direction). This gives you a much better picture of the behavior of the material.
Unfortunately, even with the stress-strain curves, you still can't necessarily tell how much of the deformation is recoverable. For linear elastic materials, such as metals, you can easily estimate how much of the total deformation is recoverable just by looking at the linear part of the curve. For nonlinear elastic materials, such as most plastics, the curve is never linear to begin with, so this approach doesn't work.
I sent an e-mail to BASF at the address listed in the press release to ask about elastic recovery. We'll see if they write back.
I second Dave Palmer's comment. These materials appear to offer strength and toughness. Would a stress-strain curve give us a better understanding of how they fail?
You certainly wouldn't use these composites in aircraft as they weigh too much and cheaper, lighter ways like foam to absorb energy over time. Nor can they be repaired, replaced nstead.
My kind of composites is whatever the job needs. I see little use for this other than boat cleats, cases, gun stocks, etc. Depends on price mostly but who needs a high priced moderately strong material?
@Jerry dycus: The repair techniques you are referring to make sense for the type of composites you are using for car bodies, which I assume mainly use thermosetting resins. But, as kurturethane pointed out, in this case we're talking about a 30 - 50% glass filled nylon injection molding compound. How would you repair that? I would imagine that the sort of repairs you're talking about would be more difficult where thermoplastic resins are involved.
While much of what you say is true, the repair part is rather off. A decent trained composite repair person can make most repairs without causing structural problems. I personally can and have made repairs for decades without hard spots in critical areas. Yes it takes more work but easily doable with training.
Your example of a 787 wing doesn't hold water. Little of the wing is critical and very resistant to battle, other damage and one of composites big advantages. About the only critical area is the wing spar/s and even there it's not as hard to repair as a metal wing. Damage other parts and all you are likely to get is a fuel leak.
As the other poster asked about fasteners, not hard either using glues, epoxies, double sided tape along with screws, bolts, etc. You can make threads, etc into composites or just wet out a bolt and hole with epoxy/glue, etc and you have a threaded hole.
One thing I rarely do is put metal in the layup as it's always a hard point and usually delaminates sooner or later. I instead put it outside the composite and glue/bolt, etc it on. If you need strength instead of metal for attachment points, I just do it in composites instead with far better, lighter results.
Nice now on the design side I can engineer these problems out.
From a marine standpoint, composite repair is as much art as science, particularly with carbon fiber. Most carbon fiber assemblies are built to be as light and stiff as possible, but are expected to flex in a specified direction and for the most part smoothly over their lentire ength. Make a repair and 99 times out of a hundred you will create a hard spot that will fracture under future loads rather than flex. Secondary adhesion is also a significant issue. The original parts are typically infushed so the fiber to adhesive ratio is carefully controlled, secondary bonds to other parts is carefully engineered and specified. Making repairs to these parts so they meet the original design parameters is almost impossible. I wouldn't want to drive a car that had "minor" crash damage and was "fixed" in a body-shop. It doesn't make sense to make a safety-critical part out of exotic material at high cost and then allow trowell on smoodge, grind away the excess and hope it meets the original design criteria. Imagine a wing section of a Dreamliner getting dinged and repaired. I'm guessing Boeing would have issues with not replacing the entire assembly.
Good summary, Dave. The information provided, including the press release, was not as clear or complete as we'd like. However, it did imply that the biggest value to these materials is the safety issue, more so than vehicle protection, and that they can return to their original shape after that much distortion.
I appreciate the perspective regarding cost to repair. My company makes products body shops use to repair plastic, so I'm familiar with this area. A 50% glass fiber nylon composite strutural component is not something that shops would or should repair. For the most part, mineral-filled PP/TPO cosmetic parts (like bumper fascia) can be repaired, but often are not. Most shops today don't have plastic repair skills and prefer to replace parts. Insurers are applying some pressure to reduce the cost to repair and now some shops are looking at plastic repair more seriously.
Using almost 200 light-emitting diodes in the front and back of the new 2014 CTS, Cadillac designers are showing how LEDs can change the character of a vehicle.
We looked at a number of sources to determine this year's greenest cars, from KBB to automotive trade magazines to environmental organizations. These 14 cars emerged as being great at either stretching fuel or reducing carbon footprint.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
