I see a parallel here, sort of, between control and machine vision. In control there's been a gulf separating the functionality and usability of Ethernet/IP versus the control-specific protocols like EtherCAT and Ethernet Powerlink. In machine vision, there's been a parallel guilf, perhaps not so large, between various open-sourced protocols like USB or GigE and their vision-specific versions like the very new USB3 Vision, and the not so new GigE Vision. And the gulfs all about that pesky determinism issue.
Ann, you have hit the nail on the head by mentioning protocols like EtherCAT. There are applications where standard Ethernet/IP can be used, but to replace the more specific bus standards like Fieldbus, you need a deterministic protocol. These have now been developed. In the IP realm, the increase in speed to gigabit and beyond helps mitigate some of the determinism issues.
The gets into the whole remote monitoring issue -- the fact that improved data links throughout the factory are enabling sensors to send data back to a central monitoring station. This, in turn, is enabling both tighter control of processes and also a reduction in outages, because failure points can be fixed right away.
That sounds like a good solution, Jack -- much more like the former process of sending reports. The real-time network, however, could send the data on a near-continuous stream. Not quite the same as letting other areas of the enterprise peek into the process to ascertain performance and results, but it would solve some of the security issues.
Rob - One possible solution to that particular problem is creating a one-way or read-only link. The data can be sent out to the IT systems, but nothing can come in that way. Yes, that adds a layer of complexity regarding updates, but it also makes sure that both the IT and Controls people sign off on the update schedules and implementations.
I hadn't heard that about safety, Rob, but unfortunately, it makes sense. Sounds like the same principle operating in both cases, of security and safety procedures. At least in the case of security, both employee training and more robust safeguards in mobile equipment were required.
Yes, I've heard that personal smartphones have entered the workplace big-time, and it's causing problems for IT departments. But it's understandable. Employees are accustomed to their Androids and iPhones, and by comparison, their work BlackBerrys are not as advanced.
Part of what's fueling the security issue is the whole trend around the consumerization of IT. More and more employees, including plant managers and operators, are bringing their own smart phones to work and want to use those devices as part of their work tasks as opposed to maintaining two devices. That makes it hard for IT or the controls group to uphold proper security standards. Also, as Ann notes, the device can get lost or the kids can log on to download some Apps and presto, you have a breach or potential security problem on your hands.
Data security is a major issue, but then it can be tackled effectively to a great extent. This initiave will definitely reduce cost implications byt enhancing remore accessing of test suites and sites
Turning off security because it gets in the way of operating the machines! That's a good one. I've seen that with safety as well, I've seen employees and managers bypass or circumvent safety in order to speed up the line.
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
7 
