HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Page 1/2  >  >>
Rob Spiegel
User Rank
Blogger
Re: Washers - relatively new electronics problems
Rob Spiegel   11/17/2011 2:29:52 PM
NO RATINGS
That's a very good question, dutchman. I've heard tons about contrl panels failing in equipment such as washers, dishwashers and refrigerators, but I haven't heard much about what caused the failures. Users shell out the bucks, replace the control panels and move on.

Maybe it is tin whiskers.

dutchman
User Rank
Iron
Re: Washers - relatively new electronics problems
dutchman   11/17/2011 11:12:29 AM
NO RATINGS
I womder if tin whisker growth have anything to do with it. (See: http://www.eetimes.com/design/military-aerospace-design/4230652/Understanding-and-mitigating-tin-whiskers?cid=NL_MilAero&Ecosystem=military-aerospace-design )


Rob Spiegel
User Rank
Blogger
Re: Washers
Rob Spiegel   11/14/2011 11:34:32 PM
NO RATINGS
Yes, Tim, there are plenty of washer stories in both the Sherlock and Monkey blogs, but most of the posts find difficulty with the control panels rather than the mechanical operation of the washer. Even with the wear and tear, washers are remarkably durable. It's the relatively new electronics that seem to create most of the problems.

thehobe
User Rank
Iron
Re: Washers
thehobe   11/11/2011 10:50:24 PM
NO RATINGS
We used a Maytag for about 7 years before the unit would not work. It seems the wiring to one of the pc boards was very loose so I recconnected the wires but the washer would still not wash. I replaced all of the power transistors on the motor control board to no avail. I finally purchased a combination motor and motor control board from Ebay, installed it and it has been working fine ever since. I was glad that I did not have to "junk" the entire unit causing global waste instead of repairing the washing machine. The loose wires appeared to be some kind of tachometer feedback to the motor control board. The loose wires may have taken out the motor microcontroller but I was not sure.

Tim
User Rank
Platinum
Washers
Tim   11/10/2011 7:25:04 PM
NO RATINGS
Washers do see a lot of force and friction during the normal operation.  It is probably one of the hardest working pieces of equipment in a house.  That may be the main reason that there are so many articles in Sherlock Ohms about washer failures.

JRThro
User Rank
Iron
Re: clothes or no clothes
JRThro   11/10/2011 4:29:44 PM
NO RATINGS
Whether or not there are clothes in the water will matter unless the density of clothing and the density of water are the same.

Dave Palmer
User Rank
Platinum
Validation and testing
Dave Palmer   11/10/2011 12:14:02 PM
NO RATINGS
This is a good example of the pitfalls of trying to validate a design solution with a test which doesn't adequately represent real-world conditions.  With a small amount of water and no clothes, replacing the pressure switch appeared to work.  It only became apparent that the pressure switch wasn't the problem when you tried to use the washing machine to actually wash clothes! Let those who are tasked with developing test and validation programs beware.

Dangela
User Rank
Bronze
dryers are much easier to work on
Dangela   11/10/2011 10:21:31 AM
NO RATINGS
When my electric dryer wouldn't heat up I would have bet money it was because the heating element went bad. It took me about an hour to tear it all apart to get to where I could ohm out the element. It tested good. I took the inpection panel off from behind the controls in a matter of seconds to see the control had melted.

gafisher
User Rank
Gold
Re: clothes or no clothes
gafisher   11/10/2011 10:18:21 AM
NO RATINGS
Wet clothes would put additional stress on the agitator regardless of water level.  It's not a weight issue per se, though it came across as that; rather, it's a loading (or drag) issue.

Dangela
User Rank
Bronze
clothes or no clothes
Dangela   11/10/2011 9:23:49 AM
NO RATINGS
I would thinnk the weight of the tub would depend solely on the level of the water, not whether there were clothes in it or not.

Page 1/2  >  >>


Partner Zone
Latest Analysis
Voting in Round 4 of our annual Gadget Freak of the Year contest is now open.
Reshoring is picking up steam, but it's not outpacing the overall continuing growth in outsourcing.
Here's a variety of views into the complex production processes at Santa's factory. Happy Holidays!
The Beam Store from Suitable Technologies is managed by remote workers from places as diverse as New York and Sydney, Australia. Employees attend to store visitors through Beam Smart Presence Systems (SPSs) from the company. The systems combine mobility and video conferencing and allow people to communicate directly from a remote location via a screen as well as move around as if they are actually in the room.
Thanks to 3D printing, some custom-made prosthetic limbs, and a Lego set, one lucky dog and a tortoise has learned new tricks.
More:Blogs|News
Design News Webinar Series
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
12/10/2014 8:00 a.m. California / 11:00 a.m. New York
11/19/2014 11:00 a.m. California / 2:00 p.m. New York
11/6/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  67


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service