That's a very good question, dutchman. I've heard tons about contrl panels failing in equipment such as washers, dishwashers and refrigerators, but I haven't heard much about what caused the failures. Users shell out the bucks, replace the control panels and move on.
I womder if tin whisker growth have anything to do with it. (See: http://www.eetimes.com/design/military-aerospace-design/4230652/Understanding-and-mitigating-tin-whiskers?cid=NL_MilAero&Ecosystem=military-aerospace-design )
Yes, Tim, there are plenty of washer stories in both the Sherlock and Monkey blogs, but most of the posts find difficulty with the control panels rather than the mechanical operation of the washer. Even with the wear and tear, washers are remarkably durable. It's the relatively new electronics that seem to create most of the problems.
We used a Maytag for about 7 years before the unit would not work. It seems the wiring to one of the pc boards was very loose so I recconnected the wires but the washer would still not wash. I replaced all of the power transistors on the motor control board to no avail. I finally purchased a combination motor and motor control board from Ebay, installed it and it has been working fine ever since. I was glad that I did not have to "junk" the entire unit causing global waste instead of repairing the washing machine. The loose wires appeared to be some kind of tachometer feedback to the motor control board. The loose wires may have taken out the motor microcontroller but I was not sure.
Washers do see a lot of force and friction during the normal operation. It is probably one of the hardest working pieces of equipment in a house. That may be the main reason that there are so many articles in Sherlock Ohms about washer failures.
This is a good example of the pitfalls of trying to validate a design solution with a test which doesn't adequately represent real-world conditions. With a small amount of water and no clothes, replacing the pressure switch appeared to work. It only became apparent that the pressure switch wasn't the problem when you tried to use the washing machine to actually wash clothes! Let those who are tasked with developing test and validation programs beware.
When my electric dryer wouldn't heat up I would have bet money it was because the heating element went bad. It took me about an hour to tear it all apart to get to where I could ohm out the element. It tested good. I took the inpection panel off from behind the controls in a matter of seconds to see the control had melted.
Wet clothes would put additional stress on the agitator regardless of water level. It's not a weight issue per se, though it came across as that; rather, it's a loading (or drag) issue.
We looked at a number of sources to determine this year's greenest cars, from KBB to automotive trade magazines to environmental organizations. These 14 cars emerged as being great at either stretching fuel or reducing carbon footprint.
Researchers at MIT and Sandia National Labs have observed a reaction in lithium-air batteries that could help improve the design of these cells for electric vehicles and other applications.
Healthcare might seem to be an unlikely target application for the Internet of Things technology, but recent developments show small ways that big-data is going to make an impact on patient care moving into the future.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
