HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
ljsdofi43092
User Rank
Iron
postcards printing
ljsdofi43092   5/31/2014 12:43:02 AM
NO RATINGS
A postcard or post card is a rectangular piece of thick paper or thin cardboard intended for writing and mailing without an envelope. There are novelty exceptions, such as wood postcards, made of thin wood, and copper postcards sold in the Copper Country of the U.S. state of Michigan, and coconut "postcards" from tropical islands.

In some places, it is possible to send them for a lower fee than for a letter. Stamp collectors distinguish between postcards (which require a stamp) and postal cards (which have the postage pre-printed on them). While a postcard is usually printed by a private company, individual or organization, a postal card is issued by the relevant postal authority.

Toronto postcards printing | Calgary postcards printing | Winnipeg postcards printing | Montreal postcards printing | Regina postcards printing | Saskatoon postcards printing | Ottawa postcards printing | Edmonton postcards printing | Vancouver postcards printing |

Atlanta postcards printing | Boston postcards printing | Chicago postcards printing | Arizona postcards printing | Miami postcards printing | New York postcards printing

Ann R. Thryft
User Rank
Blogger
Re: Double duty to the rescue
Ann R. Thryft   11/18/2011 1:28:17 PM
NO RATINGS
To answer your question, Beth, it appears that the technology has not yet been fully commercialized, since DuPont says it is still refining and testing the two methods.

RR Engineer
User Rank
Iron
Re: The Price to Upgrade
RR Engineer   11/1/2011 11:06:03 AM
NO RATINGS
The method is limited to THICK parts with a means to complete PACK in the Mold.

I have adding mold melt "PACK" volumteric make up and reduce "shrink" by:

1. Core Pin as a Plunger in the sprue puller - problem with gate size for balanced "INPUT"

2. Collapsible Cavity to build accept added melt volume and post PACK compression  

3. Side Pocket with a gate into a plunger area made up on the parting line.

4. Looking at a 40 second cycle is long. We are in 24 - 36 - 48 - 64 - 96 - 128 cavity clossure tops and bottoms with 15 - 25 second cycles.

Tim
User Rank
Platinum
Question on dosing
Tim   10/31/2011 9:35:31 PM
NO RATINGS
I am a little confused on how this technology is used especially in regards to the moving side mold cylinder.  Where does the dosed melt cushion come from on the moving side of the mold.  I can sort of understand adding material through the hot runner, but this is still hard to grasp.  In most injection molding applications, all of the fill, pack, and hold pressures are applied by the injection screw.  The length of time for pack and hold are determined by the gate freeze off time.  Some better description of what this technology does would help in applying it.

williamlweaver
User Rank
Platinum
The Price to Upgrade
williamlweaver   10/31/2011 9:53:03 AM
NO RATINGS
Like most innovations, the total cost of adoption is based on the predicted savings and the cost to upgrade. 30% time savings is really attractive in a high-volume process, but that will be balanced by the cost to modify or replace the existing tools. I'm going to guess that DuPont has done their homework and charted a path that includes the cost of tool upgrades. Otherwise this innovation will take a large time to permeate production floors as they replace older equipment or build new lines.

Beth Stackpole
User Rank
Blogger
Double duty to the rescue
Beth Stackpole   10/31/2011 8:01:57 AM
NO RATINGS
Seems like a really promising technology and one that could have significant ramifications for manufacturers given the widespread use of injection molding in production. Is this a technology experiment or is DuPont further along in terms of trials or early use case testing, or perhaps even gearing up to commercialize the technology?



Partner Zone
Latest Analysis
The popularity of Pokemon Go may be break open a new rush of augmented reality products.
Engineers in Australia have discovered a mechanism that could allow for the design of new composite materials for light harvesting and optoelectronics.
Here's a blast from the Gadget Freak past. Check out these gadgets, from telescope warming to keyboards on your fingers
A new method of modeling how they are created with chemical vapor deposition (CVD) could reduce the cost of carbon nanostructures used for for research and commercial applications, including advanced sensors and batteries.
BMW has already incorporated more than 10,000 3D-printed parts in the Rolls-Royce Phantom and intends to expand the use of 3D printing in its cars even more in the future. Meanwhile, Daimler has started using additive manufacturing for producing spare parts in Mercedes-Benz Trucks.
More:Blogs|News
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jul 11 - 15, Embedded System Design Techniques™ - Debugging Real-time Embedded Software – Hands on
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9 | 10


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Technology Marketplace

Copyright © 2016 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service