HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  RESOURCE CENTER  |  INDUSTRIES
User Rank
Platinum
Re: Temperature Rise with Pressure
11/4/2011 4:53:28 PM
NO RATINGS
The temperature changes with friction and pressure changes are very predicable with a good thermodynamics treatment from a Thermo textbook or Engineering Handbook.  This is fairly straightforward when operating away from a phase change condition, but get much more complex when shifting through partially saturated two-phase conditions.

All that being stated, It makes sence that since you are simply scaling-up a functioning pilot system. You could calculate your pilot plant system plumbing Reynolds number and size your scaled-up production system, with Reynolds number guidance, to have the same or lower pressure drop to avoid excessive heating of the fluid in your plumbing.

User Rank
Blogger
Do you have a Sherlock Ohms case to tell?
11/1/2011 6:07:16 AM
NO RATINGS
We're looking for your stories to add to the Sherlock Ohms blog.

Send along your problem and solution. About 300 words or more. We'd love to know how you soplved a tricky engineering challnege.

Send to rob.spiegel@ubm.com

User Rank
Platinum
getting out of hot water.
10/29/2011 12:16:31 PM
NO RATINGS
Pressure drop will always cause a temperature rise proportional to flow. I used this in a test stand to heat oil to 300 degrees F, and not have any risk of overheated heating elements. My customers were amazed, and then very pleased, that it worked very well. The mechanical equivalent is the temperature rise in friction brakes as they slow a vehicle. There is a formula to convert mass flow multiplied by pressure drop across an orfice to temperature rise, unfortunately I don't have it handy.

What I find amazing is that there is a pump able to produce that high a pressure at a flow rate high enough to cause heating.

User Rank
Platinum
Questioning Looks
10/28/2011 8:21:53 PM
NO RATINGS
I am surprised at the little faith that your scientist and chemist colleagues had in your setup.  I would that they would be smart enough to know that you weren't heating the water on purpose and that there would be a solution somewhere.  As you stated you need energy to make heat and removing that energy would remove the heat and save the molecules.

User Rank
Blogger
10/28/2011 10:01:38 AM
NO RATINGS
Sounds like a case of thermodynamics in action...

 Partner Zone
Latest Analysis
In a bid to boost the viability of lithium-based electric car batteries, a team at Lawrence Berkeley National Laboratory has developed a chemistry that could possibly double an EV’s driving range while cutting its battery cost in half.
The Chinese are investing in the people and the infrastructure that will make the Chinese MEMS industry competitive in the world economy — with hopes of being the best.
Using Siemens NX software, a team of engineering students from the University of Michigan built an electric vehicle and raced in the 2013 Bridgestone World Solar Challenge. One of those students blogged for Design News throughout the race.
Datalogic Automation has introduced four specific lines of encoders that enable smart motion control in a range of industrial automation applications.
Robots that walk have come a long way from simple barebones walking machines or pairs of legs without an upper body and head. Much of the research these days focuses on making more humanoid robots. But they are not all created equal.
More:Blogs|News
From Dell / Intel®
Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013    7
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
Most recent post: Ralphy Boy
From Dell / Intel®
Trey Morton, Dell, 4/25/2013    3
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
Most recent post: Cabe Atwell
From Dell / Intel®
Kirsten Billhardt, Manufacturing Industry Marketing Strategist, Dell, 3/26/2013    6
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
Most recent post: Ockham
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Dec 2 - 6, Protecting Your Embedded System From Hacking & Theft
SEMESTERS: 1  |  2  |  3  |  4