If you revamp and update this device, you could submit it to the Design Gadget Freak column. We pay $500 for complete Gadget Freak entries. If you're interested, send me a note at rob.spiegel@ubm.com and I'll send along the details.
Nowadays, I would update the power supply with a voltage regulator IC and update the op amp, but I think you'll like the simplicity. Hint: two precision thermistors, a 25-turn pot and a voltage comparator op amp.
The regular Gadget Freak is the presentation of a gadget that has been submitted to us. It includes a video, photos, a schematic, building instructions and a BOM.
The Gadget Freak Jr.s is when we find a gadget presentation online and we send along the presentation and links. It's more like reporting on gadgets out in the world.
Points well taken, George. I tried the link above the video for the build instructions and it's working. The build instructions also include the schematic.
If the link still doesn't work when you clink on it, you might try another browser.
We include build instructions, a schematic, photos, a BOM, and a video with every Gadget Freak. Those are the minimum requirements.
Gadget Freak Jr. is different in that it's more of a reported story rather than a full Gadget Freak.
I grew up on Popular Electronics. Every project was very well documented with schematics and wiring diagrams and parts lists. I seem to see too many of these GF articles not even up to the standards of PE in the good old days - 50's and 60's.
This column needs to be presented with better editing. I agree that many of these GF cases are incomplete and have indecipherable or incorrect schematics and incomplete parts lists like this one and dead end links. Even Design News has had too many errors lately.
I know the audience is full of engineers but who needs to have work so hard to read the article? When these projects are presented with a half baked presentation it is disrespectful to the author and to the readers. And a pain in the @ss to read. It takes the fun out of it.
So PLEASE put a little time into editing and put everything, photos, schematics, BOM's etc into the article on the same page or have links that work.
I found that a far simpler means of solar water heating was to submerge a black plastic sheet in the pool when it was not in use. The sheet did ned to be well below the surface, so as to heat a larger volume of water, it could even be on the bottom, out of the way. It was not hard to remove for serious pool use, and it consumed no energy, and it was very cheap.
Most gadget freak write-ups, it appears to me, are incomplete in one way or another. The result is that the missing order number for the dual temperature controller is to be expected. Just attempt to find a circuit, or some other critical build information. Usually some vital information is missing. That is what to expect.
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
7 
