HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Ivan Kirkpatrick
User Rank
Platinum
Evolution at work
Ivan Kirkpatrick   10/25/2011 11:54:08 AM
NO RATINGS
Good example of evolution at work. Improvements in one place, i.e. multicore chips, lead to improvements in  others like powertrains.  

I thought this required changes in compiler design to take advantage of multicore chips.  Perhaps that was in the cae of parallel programming.  I am not sure that applies here but perhaps someone could speak up on that.

I would also expect the multicore design to be extended to additional cores just like our workstations are now quad core, hexcore or even octo core designs.  I think this saves power on the chip as well since the multicores reduce the need for higher clock speeds.

kjd
User Rank
Iron
Re: Evolution at work
kjd   10/26/2011 11:35:43 AM
NO RATINGS
Compilers have been/are being updated to support multicore for the appropriate platforms.

However, multicore processors may be used without the hard requirement for a multicore-aware compiler. It depends on the actual chip architecture, as well as the software application design and partitioning.

sensor pro
User Rank
Gold
Re: Evolution at work
sensor pro   10/26/2011 1:01:58 PM
NO RATINGS
very good point. I did not even think about this fact.

Thanks

Tool_maker
User Rank
Platinum
Re: Evolution at work
Tool_maker   10/27/2011 6:43:27 AM
NO RATINGS
Can anyone explain this to me? In 1972 I bought a new Dodge Colt 1600, made by Mitsubishi. It could seat 4 normal sized adults, regularly got 40+ miles to the gallon and had enough get up that I got a ticket for doing 77 in a 60 mph zone. (I was younger then, so cut me some slack.) It had a 2bbl carb and coil ignition so I imagine the exact same vehicle would perform better today with fuel injection and electronic ignition. The car cost about $2200 as I recall and the only extraordinary maintenance I had was to replace the differential at about 55 thousand miles.

For some reason other cars liked to run into it while parked, sitting at a stop sign or just drivng normally. After the 4th such occurance we got rid of it. My question: how is it that a car like that could be built in the early 70's, without onboard computers, 40-70 pounds of wire, etc. Are we not smarter today? I'm just asking.

jroesch
User Rank
Iron
Re: Evolution at work
jroesch   10/27/2011 2:25:46 PM
NO RATINGS
Hello Iron,

This article should give you a little background...

http://articles.latimes.com/2011/apr/01/news/sc-dc-0402-traffic-fatalities-20110402

Because of added safety features, infotainment, SMOG control the actual weight of cars has risen substantially over the years.

Also on a plus...

Technology is getting us back on track to the 40mpg 4-door of the past!

 

Jerry dycus
User Rank
Gold
Re: Evolution at work
Jerry dycus   1/3/2012 9:49:29 AM
NO RATINGS
 

                  Ah, complication equals profit when these many units start dying.

                  And making a car engine in service that gets 7% of it's fuels energy to move it to 8% for all that cost is just not smart.  Far better go directly to EV drive with it's 20-65% eff depending on the power source.

                 The only eff way to use an ICE is running at constant speed driving an alternator which doesn't require complicated junk to be eff, cleanish as an ICE can be.  The Lotus EV Range Extender is an example of the future ICE in vehicles.

                Far cheaper is lighter unibodies, better aero and even chopping off a wheel you get into the 100mpg and up class.  Even the smaller SUV's could do this if they wanted to.



Partner Zone
Latest Analysis
Some of our culture's most enduring robots appeared in the 80s. The Aliens series produced another evil android, and we saw light robot fare in the form of Short Circuit. Two of the great robots of all time also showed up: The Terminator and RoboCop.
Two students have created a voice-command system for our homes, based on the simple and affordable Raspberry Pi.
Optomec's third America Makes project for metal 3D printing teams the LENS process company with GE Aviation, Lockheed, and other big aerospace names to develop guidelines for repairing high-value flight-critical Air Force components.
This Gadget Freak review looks at a cooler that is essentially a party on wheels with a built-in blender, Bluetooth speaker, and USB charger. We also look at a sustainable, rotating wireless smartphone charger.
Texas Instruments is rolling out a new microcontroller that could make the design of sensor networks and data logging systems simpler and less costly.
More:Blogs|News
Design News Webinar Series
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
6/25/2014 11:00 a.m. California / 2:00 p.m. New York
5/13/2014 10:00 a.m. California / 1:00 p.m. New York / 6:00 p.m. London
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jul 21 - 25, Design Products With Bluetooth Low Energy
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: August 12 - 14
Sponsored by igus
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service