Jerry dycus
User Rank
Re: Evolution at work
Jerry dycus   1/3/2012 9:49:29 AM

                  Ah, complication equals profit when these many units start dying.

                  And making a car engine in service that gets 7% of it's fuels energy to move it to 8% for all that cost is just not smart.  Far better go directly to EV drive with it's 20-65% eff depending on the power source.

                 The only eff way to use an ICE is running at constant speed driving an alternator which doesn't require complicated junk to be eff, cleanish as an ICE can be.  The Lotus EV Range Extender is an example of the future ICE in vehicles.

                Far cheaper is lighter unibodies, better aero and even chopping off a wheel you get into the 100mpg and up class.  Even the smaller SUV's could do this if they wanted to.

User Rank
Re: Evolution at work
jroesch   10/27/2011 2:25:46 PM
Hello Iron,

This article should give you a little background...


Because of added safety features, infotainment, SMOG control the actual weight of cars has risen substantially over the years.

Also on a plus...

Technology is getting us back on track to the 40mpg 4-door of the past!


User Rank
Re: Evolution at work
Tool_maker   10/27/2011 6:43:27 AM
Can anyone explain this to me? In 1972 I bought a new Dodge Colt 1600, made by Mitsubishi. It could seat 4 normal sized adults, regularly got 40+ miles to the gallon and had enough get up that I got a ticket for doing 77 in a 60 mph zone. (I was younger then, so cut me some slack.) It had a 2bbl carb and coil ignition so I imagine the exact same vehicle would perform better today with fuel injection and electronic ignition. The car cost about $2200 as I recall and the only extraordinary maintenance I had was to replace the differential at about 55 thousand miles.

For some reason other cars liked to run into it while parked, sitting at a stop sign or just drivng normally. After the 4th such occurance we got rid of it. My question: how is it that a car like that could be built in the early 70's, without onboard computers, 40-70 pounds of wire, etc. Are we not smarter today? I'm just asking.

sensor pro
User Rank
Re: Evolution at work
sensor pro   10/26/2011 1:01:58 PM
very good point. I did not even think about this fact.


User Rank
Re: Evolution at work
kjd   10/26/2011 11:35:43 AM
Compilers have been/are being updated to support multicore for the appropriate platforms.

However, multicore processors may be used without the hard requirement for a multicore-aware compiler. It depends on the actual chip architecture, as well as the software application design and partitioning.

Ivan Kirkpatrick
User Rank
Evolution at work
Ivan Kirkpatrick   10/25/2011 11:54:08 AM
Good example of evolution at work. Improvements in one place, i.e. multicore chips, lead to improvements in  others like powertrains.  

I thought this required changes in compiler design to take advantage of multicore chips.  Perhaps that was in the cae of parallel programming.  I am not sure that applies here but perhaps someone could speak up on that.

I would also expect the multicore design to be extended to additional cores just like our workstations are now quad core, hexcore or even octo core designs.  I think this saves power on the chip as well since the multicores reduce the need for higher clock speeds.

Partner Zone
Latest Analysis
A database containing information on over 16,000 tests done on 500 composites and other materials for wind turbine blades is now available free from Sandia National Laboratories.
Imagine being able to illegally download a physical product the same way you can with music and videos. That’s basically what’s happening with 3D printing and digital manufacturing, with huge repercussions in the intellectual property domain.
Our latest Design News Quick Poll reveals that readers are facing serious cyber security challenges.
Ford will be the first automaker to commercially use Alcoa's tough & fast Micromill aluminum alloy process and materials, debuting on several 2016 F-150 truck components. Alcoa will also license its Micromill process and materials technology to Danieli Group.
Even as an increasing number of instrument manufacturers migrate toward modern touch screens, many engineers say they still prefer the tactile feel of knobs and buttons, a new survey says.
Design News Webinar Series
10/1/2015 11:00 a.m. California / 2:00 p.m. New York
9/10/2015 11:00 a.m. California / 2:00 p.m. New York
10/20/2015 8:00 a.m. California / 11:00 a.m. New York
11/10/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 19 - 23, Embedded System Design Techniques™ - Driver Design Patterns and the Internet
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service