I think this is going to be a good technology to watch. With the government mandating higher fuel efficiencies and "good enough" battery technology still a few years away, this might be the technology that gets us there.
Proving this works in high output engines will be an important factor. It does have some interesting characteristics, for one, the hot side of the engine stays hot and the cool side does not heat up too much. This is in contrast to the Otto cycle characteristics.
I would be very curious as to just why the retardation of the spark helps so much in this design compared to the Otto cycle. And another obvious question to me is if the split cycle is amenable to creating a split Diesel cycle? Would there be any benefits in that?
Seems to me that any kind of technology that has the potential to advance the cause of fuel efficiency is to be taken seriously. Glad to hear that analyst groups and automotive OEMs have this on their radar screens even if it's some time out before we see the actual technology in production vehicles.
This sounds a lot like our two stroke engine, except for being more complicated and having six valves. Clearly it allows much more variation in timing of all the several parameters like when to start the air intake portion and when to inject the fuel. Depending on the timing requirements, the same functions could possibly be delivered by a standard two-stroke engine, even better if it had direct fuel injection. Such an engine might possibly also fare better in emissions testing, although efficiency and low emissions seldom peak at the same time. But as the split stroke is compared to a two stroke, it is clear that they are similar.
Hello to all. Scuderiengine.com answers many of your questions. THIS innovative engine technology will definitely shange the engine world (ICE) forever. Lets NOT be "Car-Centric" here. There are ICE Internal Combustion Engines in many other applications and not only the automobile. Lawnmowers, tractors, big generators, boat engines (large + small) basicly ANY ICE with piston technology. As a former Rubber+ Plastics engineer and a youthful "Motor-head",,,, I knew this project was a winner within 30 minutes of a complete inspection of their technologies and developments...
Go to the web-site. This concept "ATDC" is not only central but its been their focus for many years; at Team Scudei. I immediately invested upon being offered the opportunity to get on board with this "Gamechanger" ..
In my opinion....look at the progress and then the depth and gameplan that Scuderi employs. They are asked...they answer beyond expectations and then they engineer beyond expectations. Right now...at 65 mpg proven via simulation,,,there is talk in the 80 mpg range and a longer view of 100 mpg. Will they breach these barriers? I do not know; but they have repeatedly pushed foward beyond their expectations many times before.
Right now....I await the announcement of our 1st leassee of the technology and I am preparing for the push to "Go Public " as Sal Scuderi has stated may times in the past; as the GOAL of Scuderi Motors. The time has come for a real world demonstration. The significant strides foward can no-longer be kept in the closet. It's time to show the public and get ready for the stampede !!!!
Having a long history of watching these various technologies I am very skeptical until they actually build one and run it on a dyno or an instrumented vehicle. They need to build it and test it, otherwise it is just another idea that is good on paper but will never materialize. The world is full of failed attemps. like the ECOmotor. So far no one has been able to violate the laws of thermodynamics
Currently the most efficient practical engines are the direct injected European Diesels at over 30% actual dyno efficiency. We cannot use these in the US becaus of the high combustion pressures and temperatures (the key to efficiency) causes too much NOx
Isn't this essentially an internal supercharger? Seems a traditional supercharger would have less parasitic loss, no fricton from extra pistons and valve train, and would accomplish exactly the same thing....
I suspect that we will be using fossil fuels a lot longer than many people suspect or desire. Reducing emissions is a laudable goal but the world is going to use up all the fossil fuel we can no matter what the green climate folks would like to see happen.
I would really like to see the EV replace ICE powered ones but the target to beat is still the ICE and the availability of fossile fuels is still good enough. How good and for how long is difficult to say but we keep finding more and figuring out how to get it in a relatively cost effective manner. Oil, coal, natural gas, methane hydrates, we are going to use them all.
By experimenting with the photovoltaic reaction in solar cells, researchers at MIT have made a breakthrough in energy efficiency that significantly pushes the boundaries of current commercial cells on the market.
In a world that's going green, industrial operations have a problem: Their processes involve materials that are potentially toxic, flammable, corrosive, or reactive. If improperly managed, this can precipitate dangerous health and environmental consequences.
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is