HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
<<  <  Page 2/2
Ratsky
User Rank
Platinum
Re: Easy to work on
Ratsky   9/8/2011 1:01:46 PM
NO RATINGS
I want to assure everyone that the picture was NOT my Scamp!  It did have the 5-liter V8, but no mods of any kind (besides the addition of that star washer...).

The Technology Consortium
User Rank
Iron
Re: Easy to work on
The Technology Consortium   9/8/2011 12:17:52 PM
NO RATINGS
BTW,

I am surprised that nobody noticed the lack of Power Brakes!

Yup, I remember those days...

 

 

averagejoe72677
User Rank
Gold
Re: Star washer
averagejoe72677   9/8/2011 11:42:56 AM
NO RATINGS
I had a 1972 Dodge Dart I bought new. The electrical system in general was designed by monkeys. I was warned early on to keep a spare ignition resistor in the glove box as these fail without notice and leave you stranded. It seems Chrysler chose to run the ignition system (points) on 6 volts and the rest of the car on 12 volts. Why on earth they did that is beyond me as all other makes used 12 volt systems.

Rob Spiegel
User Rank
Blogger
Shorts in the wheel bearings
Rob Spiegel   9/8/2011 11:37:43 AM
NO RATINGS

Reader Thomas Alosso sent in this comment:

I had a Chrysler Horizon the first year that they were made and after having front wheel bearings replaced six or sever times (every 1500 miles), they finally sent a top guy out to check the car. What they found was that the ground strap from the starter to the frame ground was missing and every time the car was started all the current went through the wheel bearings and cooked them.

NdYag Junkie
User Rank
Iron
Re: Easy to work on
NdYag Junkie   9/8/2011 9:58:05 AM
NO RATINGS
 The fact these cars are easy to work on shows in the photo as the owner of this Scamp must be having a lot of fun with it. The engine compartment shows a lot of modifications from stock. Aftermarket valve covers and spark plug wires, Carter Competition Series 4 barrel carb on an aftermarket aluminum intake which necessitated the mounting of the coil on the firewall, the windshield wiper motor has been removed. A fuel pressure regulator is mounted on the inner fender panel which most likely means the car has an electric fuel pump feeding it. The heater has been bypassed or removed because the hose which typically feeds it has been rerouted to the intake manifold. This car isn't your typical "grocery getter" anymore!

Jluminais
User Rank
Silver
Roomy
Jluminais   9/8/2011 9:36:48 AM
NO RATINGS
Look at all the room in there!  I miss that.

Rob Spiegel
User Rank
Blogger
Easy to work on
Rob Spiegel   9/7/2011 12:23:45 PM
NO RATINGS
I miss those engines. They were so easy to work on. And there was tons of room. You could almost stand in the engine compartment.

TJ McDermott
User Rank
Blogger
Re: Mopar
TJ McDermott   9/7/2011 9:24:51 AM
NO RATINGS
I love the jaunty, carefree wire routing shown in the attached image as well.

Alexander Wolfe
User Rank
Blogger
Mopar
Alexander Wolfe   9/7/2011 8:28:56 AM
NO RATINGS
I had a 1973 Duster, w the famous slant 6, which was a hand-me-down from my father. The problem I had, when the car was about 15 years old, is that the column shifter wouldn't stay locked into Drive. Being disinclined to disassemble the whole steering column, I never figured out what the minor part was, that was holding the thing into the detent.

Douglas Smock
User Rank
Platinum
Star washer
Douglas Smock   9/7/2011 8:19:47 AM
NO RATINGS
A star washer is a bad --and strange-- place to look for cost reductions.

<<  <  Page 2/2


Partner Zone
Latest Analysis
Self-driving vehicle technology could grow rapidly over the next two decades, with nearly 95 million “autonomous-capable” cars being sold annually around the world by 2035, a new study predicts.
MIT’s Senseable City Lab recently announced the program’s next big project: “Local Warming.” The concept involves saving on energy by heating the occupants within a room, not the room itself.
The fun factor continues to draw developers to Linux. This open-source system continues to succeed in the market and in the hearts and minds of developers. Design News will delve into this territory with next week's Continuing Education Class titled, “Introduction to Linux Device Drivers.”
Dean Kamen tells an audience at MD&M East 2014 how his team created the DEKA Arm to meet DARPA's challenge to design a better prosthetic arm for wounded veterans.
The new draw-it-on-a-napkin is the CAD program. As CAD programs become more ubiquitous and easier to use, they have replaced 2D sketching for early concepting.
More:Blogs|News
Design News Webinar Series
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
6/25/2014 11:00 a.m. California / 2:00 p.m. New York
5/13/2014 10:00 a.m. California / 1:00 p.m. New York / 6:00 p.m. London
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Aug 4 - 8, Introduction to Linux Device Drivers
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: August 12 - 14
Sponsored by igus
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service