HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  RESOURCE CENTER  |  INDUSTRIES
<<  <  Page 2/3  >  >>
User Rank
Gold
Re:Countertop sSocks
9/6/2011 12:45:25 PM
NO RATINGS
I'm having a hard time understanding how the metal band on your countertop could act like a secondary winding driven by the primary in the base of your toothbrush holder/charger.  I have such a toothbrush and the magnetic flux in the base is so feeble that moving the tooth brush a fraction of an inch from the base stops the charging effect in the toothbrush.  I just can't see any way this weak field could induce a current flow in the counter trim strip.  Furthermore, the trim strip is essentially a one-turn secondary.  if it's a continuous strip, it's a shorted one-turn secondary with zero volts output, or if not a closed loop, and being one turn only, I believe its induced voltage would be so low as to be imperceptable.

There are other possible causes of the shock that was felt.  I would look to see if the whole bathroom lighting and accessory outlets have been wired correctly, and that the ground and hot supply leads weren't mixed up resulting in electrically hot (supposedly) grounded surfaces.

I'm sure there are other cases like this, but I clearly recall a situation in London, England where an electrician mixed the hot and ground leads to a bathroom outlet that resulted in fatally shocking the user of an electric shaver.

Myron J. Boyajian

User Rank
Iron
Info missing
9/6/2011 12:33:55 PM
NO RATINGS
Between what two points are you measuring 30 - 50V?  You can't get a shock on a closed loop with a circulating current, (see works of Kirchhoff & Lenz), so I assume you measured between the trim and ground.  If so, simply patch an incandescent bulb -any wattage- between the same two points and measure again.  I wager that the bulb will not light, and the voltage will drop to a few dozen mV, because you have a small capacitive coupling from some energized conductor to the floating trim.   Maybe the toothbrush charger or even a hair-dryer power cord.  If so, just ground the trim and fuggedaboutit.  You can feel currents too small to trip a GFCI, and it's not necessarily dangerous - just startling.

User Rank
Platinum
Re: Protection
9/6/2011 12:22:49 PM
NO RATINGS

1) I have seen these metal edges on older counters in kitchens or bathrooms to provide a dressed-up trim on either formica or tile counters.  This trim was primarily eliminated when granite, CorianTM, and laminated edges were developed and esthetically preferred.

2) I was corrected years ago, by a former Navy Officer, that "Duct" tape is properly called "Duck" tape as it was developed in WW II for the Navy primarily to use in Ships, and Submarines over asbestos pipe insulation.  Hence, the reason for the Navy Gray color. It obviously found many other uses including sealing of sheetmetal ductwork.

User Rank
Bronze
GFI
9/6/2011 9:48:02 AM
NO RATINGS
Rob,

Was the base plugged into a GFI outlet? That would have caught any leakage.

User Rank
Platinum
'nother question.
9/5/2011 11:42:19 PM
NO RATINGS
So was the countertop energized all the time or only when the toothbrush was being charged.  Also, was the change generated from the energy going from the base to the toothbrush?  How did you rule out the possibility that the base was directly influencing the trim?

User Rank
Platinum
Re: Old is new
9/2/2011 2:21:51 PM
NO RATINGS
Mr. Wolfe - your duct tape comment got a big chuckle out of yours truly!  Somebody is having a good day!

User Rank
Blogger
RE: Shocking Bathroom Countertop
9/2/2011 12:22:51 PM
NO RATINGS
Hi Bob,

I think your story would make a good Sherlock Ohms posting. If you;re interested, please flesh it out with a tad more detail and send it along to: rob.spiegel@ubm.com

I hope to see it.

User Rank
Platinum
RE: Shocking Bathroom Countertop
9/2/2011 11:42:13 AM
NO RATINGS
I totally agree with 'armorris' on this - the problem could not (well, let me rephrase that a bit - it is highly improbable) be due to the toothbrush charger coupling to the metal rim.  There is a leakage path someplace and I would seriously suggest some more aggressive work to figure out what it is.  Having something put 30 to 50 V out there is NOT a good thing.

I had a somewhat similar situation a good many years ago. I had added a workbench in a bedroom which was located in the basement (the bedroom and the interior wiring had been added by the previous owner) and, when the workbench's outlets were plugged into the wall outlet, I was getting a 'tingle' when I held a grounded tool.  Not good.

I tore into the electrical system downstairs and finally found the culprit - on one of the metal boxes on a homemade extension cord, the screw on the cord clamp was too long and was contacting the hot wire in the cord.  This essentially put 120VAC on the ground - the connection was not solid enough for a 'solid' short but did manage to drag the grounds up to about 50 V above earth ground.  A very solid 'tingle' indeed.

My recommendation: find the 'real' problem.

User Rank
Platinum
Re: Old is new
9/2/2011 11:20:26 AM
NO RATINGS
I'm a retired Electrical Engineer. It is not possible for the coil in the toothbrush charger to induce 30-50 volts into the metal trim on the countertop. That kind of voltage can only come from leakage. If removing the toothbrush charger fixed the problem, then insulation leakage in the charger base is the problem and water has conducted the current to the metal trim. The coupling between the primary coil in the charger (60Hz to maybe 75KHz) is far too small to induce such voltage into the trim on the countertop.

User Rank
Blogger
Re: Protection
9/2/2011 9:22:03 AM
NO RATINGS
Funny that the charge didn't happen immediately after using the electric toothbrush, or did it? I guess you can count me in with the others who would have opted to replace the counter top because of many reasons, including the charge. But the fix definitely would not have been done with duct tape--white color or otherwise!

<<  <  Page 2/3  >  >>

 Partner Zone
Latest Analysis
When Dick Neubert discovered that his fireplace's heatilators lost heat when not in use, he created a gadget to rectify the situation.
Microsoft will quit supporting – and patching – Windows XP in April. This may be a cruel development for plants.
Injection molding can be a powerful tool for both prototyping and production. Here are some tips on how design engineers can get the most out of it.
Truchard will be presented the award at the 2014 Golden Mousetrap Awards ceremony during the co-located events Pacific Design & Manufacturing, MD&M West, WestPack, PLASTEC West, Electronics West, ATX West, and AeroCon.
In a bid to boost the viability of lithium-based electric car batteries, a team at Lawrence Berkeley National Laboratory has developed a chemistry that could possibly double an EV’s driving range while cutting its battery cost in half.
More:Blogs|News
From Dell / Intel®
Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013    7
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
Most recent post: Ralphy Boy
From Dell / Intel®
Trey Morton, Dell, 4/25/2013    3
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
Most recent post: Cabe Atwell
From Dell / Intel®
Kirsten Billhardt, Manufacturing Industry Marketing Strategist, Dell, 3/26/2013    6
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
Most recent post: Ockham
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Dec 16 - 20, Introduction to SCADA Security
SEMESTERS: 1  |  2  |  3  |  4