HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
William K.
User Rank
Platinum
Low efficiency beacon symptom
William K.   9/23/2011 9:18:01 PM
NO RATINGS
The problem of moisture absorbtion is often nonlinear, which is why just baking the deteriorated units would not result in another five years of service. What probably happened is that after a bit of exposure the more moisture resistant portion deteriorated and the more porous material was exposed, at which point the process went much faster. So baking and re-coating could have been a solution, but the cost would probably be similar to installing a new antenna. Sometimes repairs are completely possible but not economical to do. Given what I know about high labor costs on railroads, I would presume that was the case here.

Yes, it was good detective work, although great detective work would have been to stop and think for a while and come with a suspect at the beginning.

dhall
User Rank
Iron
Re: Troubleshooting
dhall   9/1/2011 8:45:23 PM
NO RATINGS
If the parts absorbed moisture, why wouldn't baking them drive the moisture out and give you another 5 years of operation?  Obviously the design was faulty, but cycling the devices periodically through a drying operation could potentially save having to replace them unless they were very inexpensive and the cost of handling exceeded the replacement cost.

plasticmaster
User Rank
Silver
Re: Troubleshooting
plasticmaster   9/1/2011 9:30:42 AM
NO RATINGS
PTFE (DuPont "Teflon") is hydrophobic (water repelling). PET (material of the aforementioned housing) is hygroscopic (water absorbing). I know long term testing is sometimes sacrificed in order to get product to market. In this case the product worked for 5 years before failure. I would imagine, realistically, that when the problem was discovered, the solution would be to change the material to something better suited for long term outdoor use.

Sometimes the more expensive material is the cheaper (or should I say, more economical) and better choice in the long run.

tjgau
User Rank
Iron
Re: Troubleshooting
tjgau   8/31/2011 9:36:05 PM
NO RATINGS
I think it would have been a combination of incomplete specification & manufacturing (Moulding process & cleanness).
The materials used were those specified by the original European design. The manufacture of this product was taken over by another company shortly after so there was no further trend analysis data to see if the problem continued to other batch lots.

Toni

Jack Rupert, PE
User Rank
Platinum
Re: Troubleshooting
Jack Rupert, PE   8/31/2011 7:56:03 PM
NO RATINGS
So, was the root cause of the problem a specification problem, material choice, or manufacturing?

Tim
User Rank
Platinum
Troubleshooting
Tim   8/31/2011 5:32:02 PM
NO RATINGS
Good troubleshooting. It shows that even solid components can have a problem in them.



Partner Zone
Latest Analysis
Factory floor engineers may soon be able to operate machinery and monitor equipment status simply by tapping their eyeglasses.
GE Aviation not only plans to use 3D printing to mass-produce metal parts for its LEAP jet engine, but it's also developing a separate technology for 3D-printing metal parts used in its other engines.
In this TED presentation, Wayne Cotter, a computer engineer turned standup comic, explains why engineers are natural comedians.
IBM's new SyNAPSE chip makes it possible for computers to both memorize and compute simultaneously.
The “Space Kid,” 11, will be one of the first civilians to have his design manufactured in space by NASA, thanks to the City X Project, which inspires kids to think about new 3D-printed inventions that could be useful for humans living in space.
More:Blogs|News
Design News Webinar Series
9/10/2014 11:00 a.m. California / 2:00 p.m. New York
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
6/25/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Sep 22 - 26, MCU Software Development – A Step-by-Step Guide (Using a Real Eval Board)
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: September 30 - October 2
Sponsored by Altera
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service