HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
William K.
User Rank
Platinum
Low efficiency beacon symptom
William K.   9/23/2011 9:18:01 PM
NO RATINGS
The problem of moisture absorbtion is often nonlinear, which is why just baking the deteriorated units would not result in another five years of service. What probably happened is that after a bit of exposure the more moisture resistant portion deteriorated and the more porous material was exposed, at which point the process went much faster. So baking and re-coating could have been a solution, but the cost would probably be similar to installing a new antenna. Sometimes repairs are completely possible but not economical to do. Given what I know about high labor costs on railroads, I would presume that was the case here.

Yes, it was good detective work, although great detective work would have been to stop and think for a while and come with a suspect at the beginning.

dhall
User Rank
Iron
Re: Troubleshooting
dhall   9/1/2011 8:45:23 PM
NO RATINGS
If the parts absorbed moisture, why wouldn't baking them drive the moisture out and give you another 5 years of operation?  Obviously the design was faulty, but cycling the devices periodically through a drying operation could potentially save having to replace them unless they were very inexpensive and the cost of handling exceeded the replacement cost.

plasticmaster
User Rank
Silver
Re: Troubleshooting
plasticmaster   9/1/2011 9:30:42 AM
NO RATINGS
PTFE (DuPont "Teflon") is hydrophobic (water repelling). PET (material of the aforementioned housing) is hygroscopic (water absorbing). I know long term testing is sometimes sacrificed in order to get product to market. In this case the product worked for 5 years before failure. I would imagine, realistically, that when the problem was discovered, the solution would be to change the material to something better suited for long term outdoor use.

Sometimes the more expensive material is the cheaper (or should I say, more economical) and better choice in the long run.

tjgau
User Rank
Iron
Re: Troubleshooting
tjgau   8/31/2011 9:36:05 PM
NO RATINGS
I think it would have been a combination of incomplete specification & manufacturing (Moulding process & cleanness).
The materials used were those specified by the original European design. The manufacture of this product was taken over by another company shortly after so there was no further trend analysis data to see if the problem continued to other batch lots.

Toni

Jack Rupert, PE
User Rank
Platinum
Re: Troubleshooting
Jack Rupert, PE   8/31/2011 7:56:03 PM
NO RATINGS
So, was the root cause of the problem a specification problem, material choice, or manufacturing?

Tim
User Rank
Platinum
Troubleshooting
Tim   8/31/2011 5:32:02 PM
NO RATINGS
Good troubleshooting. It shows that even solid components can have a problem in them.



Partner Zone
Latest Analysis
Take a peek into the world of a test engineer – and then tell us about yourself! We want to know what part each of our readers plays in the wonderful umbrella known as design engineering.
On Sunday, when more than a hundred million Americans turn on their televisions to watch the Super Bowl, they might consider first giving thanks to a polymer known as polybutadiene. .
Design News is pleased to present the finalists in the Design Tools - Hardware & Software category of our 2016 Golden Mousetrap Awards.
The series now can interface with a wider array of EtherNet/IP-compliant hardware across many industrial sectors, including factory automation systems, plastic injection molding apparatus, and materials-handling equipment.
Gadget freaks at the Pacific Design & Manufacturing Show in Anaheim next week are in for a special treat: a chance to participate in a slot car competition on the show floor.
More:Blogs|News
Design News Webinar Series
1/28/2016 11:00 a.m. California / 2:00 p.m. New York
12/8/2015 11:00 a.m. California / 2:00 p.m. New York
2/18/2016 11:00 AM PT | 2:00 PM ET
2/24/2016 11:00 AM PT | 2:00 PM ET
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jan 11 - 15, Designing ARM Devices Using Segger Tools
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2016 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service