Me too, Noswad. At VHF frequencies, the interference (which originates with the sparking of the motor's commutator) will be severely attenuated as it propagates through the premises wiring. So it's very unlikely that it's conducted from source to victim. Instead, the VHF noise will be radiated from the first foot or two of wiring connected to the brushes ... and this is where clamp-on ferrite chokes are very useful at spoiling the efficiency of the inadverdent antenna.
I have a hard time understanding how emissions from the motor got picked up by the wireless system from that distance. I was thinking more along the lines of power line noise.
This sounds way too oversimplifed. I work in the area of pro audio and have helped thousands of customers find all sorts of problems. What's hard to believe is that, because wireless mics operate at VHF frequencies where wavelengths are only a few feet, just insulating a motor (presumably from surrounding metal work) would have any effect at all. Generally, to reduce emissions caused by arcing (brush motor in this case), some filtering has to be applied as close to the brush connections as possible ... sometimes the filtering is as simple as snapping some ferrite choke cores around the radiating wires. I'd like to know more about the solution.
This is quite interesting, moreso when you considr that the "short wireless link" was probably FM. A correctly functioning link would have the receiver in a full quieting mode, meaning that there was enough signal to saturate the limiter stages, which is what allows FM to provide the much desired noise elimination. The signal from the sparking elevator drive motor should not have been strong enough to get past the limiter stages, leading to my guess that the radio signal amplitude was not nearly as high as it should have been. So perhaps there was a failure there some place.
One more question, which is, why didn't they check the wireless link first thing? LInks are almost always a source of noise in an otherwise silent system,
On the other side, what kind of company has an elevator that is only used by a security guard on Sunday? That is a bit puzzeling, I think. Must business elevators get used more during the weekdays.
Our church had a noise problem on some Sunday mornings years ago, before wireless mikes were used. It was a random, distorted squawking sound, in short bursts with long pauses between. Usually it was weak and ignorable, but now and then it was loud. Some of us started to recognize it as distorted speech. Turns out that one member's husband often drove her to church, but sat in the car in the parking lot during services. Then he got a CB radio, with a (illegal) power amplifier, to pass the time. Depending on how close to the sanctuary he parked, his calls got into the amplifier system! Just asking got him to stop (or move a block away), but we had to add lots of RF chokes and bypasses to make sure that other stray RF stayed out of the system.
This story shows that you can not give up when troubleshooting. Once you have eliminated all of the causes, check again because you may have missed something.
When I was in Technical Support in Michgan Bell, we got a series of Sunday morning crosstalk complaints from a neighborhood surrounding a particular church. Turned out the services were broadcast over a local radio station, they had leased a dry pair from Bell to get the audio. Investigation showed they had connected the pair to the 70 volt line terminals of the church's PA system. When the Rev got to the Turn or Burn part, everybody on the phone within a half mile got the message.
I guess you could call this a case of elevated noise. I love it when the Sherlock Ohms mysteries end up being some oddball element outside the immediate area of the problem.
As energy efficiency becomes more and more a concern for makers of electronics devices, researchers are coming up with new ways to harvest energy from sound vibration, footsteps, and even electromagnetic fields in the air.
The government wants to study your brain, and DARPA wants to use similar information to give robots true autonomy beyond any artificial intelligence developed to date. Sound like science fiction? It's not.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
