It reminds me of a buried receptacle I had to deal with as a teenager.
I had installed it in a frame addition to the customer's trailer on Lake Norman, NC. Days later, he called my father and said that he had paneled the room and the receptacle wasn't there. My father looked at me sternly and informed me of this. I told him that the customer must have been drunk when he did the paneling - how else could he miss the box sticking out a quarter-inch from the studs? My dad just told me to go fix it.
I got on-site and could see the bulge in the wall where the receptacle was hiding. The only problem was that it was "hot" and the breaker box was in the trailer, which was locked. My perenially inebriated assistant still didn't understand that it was simply a matter of judiciously cutting the paneling to reveal the receptacle and then screwing on the cover plate. He looked at the concrete floor and said, "Gonna be mighty hard pulling the wire through that concrete floor!"
I took a keyhole saw and bumped it into the paneling where I guessed was the edge of the box. As luck would have it, it went into the "hot" hole in the receptacle and sent me flying! My assistant exclaimed, "Told you gonna be hard pulling that wire through that concrete floor!"
Ten minutes later, the job was done. A month later, I was off to MIT to study electrical engineering.
The reason the signal was stronger at the box is that the box served as additional radiating surface, ( a bigger antenna), which is why the signal was stronger. This would be the case even if the wire was simply cut off and coiled up in the box. The other reason that it worked in this instance is that the box was at the end of the wire.
This is an old trick used by alot of old tech like me. I use it for locating bad connection in the breaker panel, bad switches, loose connections, etc.
in the old days we would just roll all the wires into the box, but later the electrical code required that for the rough-in to be complete the wires would be connected as they would be when the installation was complete except for the wiring device (outlet), so the hash would propagate from box to box, no problem. also a set of plans could locate the box to within a few feet, then use the transistor radio from there. the box location would usually give off a stonger signal due to the ball of wire in the box.
Most likely the direction or quantity of feeder lines changes at a junction box. Another option is that the electrical bos is/was metal, acting as a shield to reduce the noise radiation.
It is clever to use a portable radio with a ferrite loop antenna to detect the brush noise, but I agree the signal would not be significantly stronger at the box than along the wiring leading to it. Perhaps once this method had located the general area, one might use a metal detector, an RF based stud-finder, or even a pocket compass to find the exact spot. All this assumes that the electrician was not so sloppy as the dry-waller and used a traditional steel box.
I agree with Beth, but Bob is right to question why the box was so far back that it could have drywall run right over it and not need a cutout. That is just plain poor work quality. Having done a whole lot of reworks of other peoples installations, it is clear that lazy construction practices make everybody else's work more difficult for many years to follow.
Of course, I am aware that if the box needs a cutout then the sheetrock installer needs to do more work, which does make the whole job take longer, but if the electrician needs to fight with a box that is set back to far, that also takes more time as well.
For 3D printing to make the jump from rapid prototyping to manufacturing, engineers will need to find easier ways to move products from their CAD screens to their printers.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
New versions of BASF's Ecovio line are both compostable and designed for either injection molding or thermoforming. These combinations are becoming more common for the single-use bioplastics used in food service and food packaging applications, but are still not widely available.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
0 
