The most important answer is hidden behind these words:
Finally, rare earth materials for permanent magnets are relatively expensive and may be in limited supply for some markets, due to geographic concentration of the common raw materials suppliers.
This means: China is the only producer of rare earth magnets, (all other rare earth minig sites closed down) and now we can kiss them goodbye.
You do need a motor dive to operate a SynRM, but that type of drive is significantly less complex than a VVVF drive used for varying induction motor speed. They're not much more complex than 'soft-start' controllers. Given the dramatic reduction in the costs for all types of motor controls over the past 20 years, the cost of the drive electronics for a SynRM are going to be modest in all but the most cost sensitive applications. Additionally, the operating cost savings are likely to largely offset the cost of any drive electronics.
My experience with SynRM are that, by their nature, they generate significantly more torque ripple than an induction motor. Has this been remedied or did the author simply fail to mention it as a factor to be considered in selecting a SynRM for an application?
An induction motor can only run below synchronous speed because the rotor field is generated by the slip speed between the stator and the rotor. The power used to create the rotor magnetic field is the loss mentioned by others. The strength of the induction motor is that as the load increases the slip also increases, which increases the current and magnetic field in the rotor. IT works well, but it uses more power than the synchronous motor. ON the other side, the synchronous motor is driven by the rotating magnetic field dragging the rotor magnets around. The problem with an ordinary synchronous motor is that when the load increases a point is reached where it falls out of synchronization and then stalls. This is great if you seek to have a very reliable means to limit torque, otherwise it is a problem. A hybrid motor that will continue to deliver torque as the load increases would be very handy, and it could probably be easier to control the speed with a VF drive. Also, it might wind up having a greater efficiency, which is a definite goal.
Is it possible to provide a more detailed description about how it provides this new function?
Is the breakthrough the gains in efficiency when compared to squirrel cage designs? SRM's have been around for quite a while and the main problem associated with this technology has always been in the drive electronics - it is difficult to manage this type of motor without sophisicated controls.
Congratulations, this is a great idea. You guys did a great job. We can always use a little more efficiency, and this will pay off big time in large scale, continuosly running operations...
This story is very timely given the increased interest, and deployment of, energy efficient motors. I'll be writing about that, and about the results of a reader survey we did on energy efficient motors and drives, in the September issue of Design News.
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
7 
