HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
REGISTER   |   LOGIN   |   HELP
lcelectro
User Rank
Iron
all the answers
lcelectro   1/15/2012 5:54:12 PM
NO RATINGS
You can find all the answers at the ABB Review at

http://www05.abb.com/global/scot/scot234.nsf/veritydisplay/46ab92b48dda3f248325785c005a701a/$file/ABB%20Review%20ENG%201_11-0204_CMarticle.pdf

The most important answer is hidden behind these words:

Finally, rare earth materials
for permanent magnets are relatively expensive
and may be in limited supply for
some markets, due to geographic concentration
of the common raw materials
suppliers.

This means: China is the only producer of rare earth magnets, (all other rare earth minig sites closed down) and now we can kiss them goodbye.

N. Christopher Perry
User Rank
Gold
Re: What is the breakthrough?
N. Christopher Perry   9/9/2011 10:31:32 AM
NO RATINGS
You do need a motor dive to operate a SynRM, but that type of drive is significantly less complex than a VVVF drive used for varying induction motor speed.  They're not much more complex than 'soft-start' controllers.  Given the dramatic reduction in the costs for all types of motor controls over the past 20 years, the cost of the drive electronics for a SynRM are going to be modest in all but the most cost sensitive applications.  Additionally, the operating cost savings are likely to largely offset the cost of any drive electronics.

N. Christopher Perry
User Rank
Gold
Torque Ripple
N. Christopher Perry   9/9/2011 10:25:00 AM
NO RATINGS
My experience with SynRM are that, by their nature, they generate significantly more torque ripple than an induction motor.  Has this been remedied or did the author simply fail to mention it as a factor to be considered in selecting a SynRM for an application?

William K.
User Rank
Platinum
Synchronous induction motors?
William K.   8/17/2011 12:31:05 PM
NO RATINGS
An induction motor can only run below synchronous speed because the rotor field is generated by the slip speed between the stator and the rotor. The power used to create the rotor magnetic field is the loss mentioned by others. The strength of the induction motor is that as the load increases the slip also increases, which increases the current and magnetic field in the rotor. IT works well, but it uses more power than the synchronous motor. ON the other side, the synchronous motor is driven by the rotating magnetic field dragging the rotor magnets around. The problem with an ordinary synchronous motor is that when the load increases a point is reached where it falls out of synchronization and then stalls. This is great if you seek to have a very reliable means to limit torque, otherwise it is a problem. A hybrid motor that will continue to deliver torque as the load increases would be very handy, and it could probably be easier to control the speed with a VF drive. Also, it might wind up having a greater efficiency, which is a definite goal.

Is it possible to provide a more detailed description about how it provides this new function?

rosek
User Rank
Silver
What is the breakthrough?
rosek   8/17/2011 9:37:57 AM
NO RATINGS
Is the breakthrough the gains in efficiency when compared to squirrel cage designs?  SRM's have been around for quite a while and the main problem associated with this technology has always been in the drive electronics - it is difficult to manage this type of motor without sophisicated controls. 

ChrisP
User Rank
Silver
How can this be said to be anything to do with PM motors?
ChrisP   8/17/2011 12:51:54 AM
NO RATINGS
It does not have any magnets in it at all and no brush gear.  Maybe they meant stepper motor.

What we need are smaller motors in this technology that are quiet and efficient.

Greg Stirling
User Rank
Platinum
Synchronous Reluctance Motor Breakthrough
Greg Stirling   8/15/2011 2:31:37 PM
NO RATINGS
Congratulations, this is a great idea.  You guys did a great job. We can always use a little more efficiency, and this will pay off big time in large scale, continuosly running operations...

TJ McDermott
User Rank
Blogger
When!?
TJ McDermott   8/15/2011 12:16:24 PM
NO RATINGS
This is exciting!  When can we expect to see these new motors (espeically in the smaller frames)?

Alexander Wolfe
User Rank
Blogger
Efficieny rules
Alexander Wolfe   8/15/2011 11:21:10 AM
NO RATINGS
This story is very timely given the increased interest, and deployment of, energy efficient motors. I'll be writing about that, and about the results of a reader survey we did on energy efficient motors and drives, in the September issue of Design News.



Partner Zone
Latest Analysis
Today's robots should be respected, and humans should be wary of their growing skills and sophistication. Quite simply, robots are better than us in a lot of ways. Here are 10 of them.
3D printing has met up with drones in a 3D-printed UAV. University of Sheffield engineers printed the prototype drone in 24 hours from ABS plastic using Fused Deposition Modeling.
Product design is changing with advances in technology and outsourced manufacturing. The Art of Product Design spells out the future of design engineering.
AMD is set to launch the industry's first 16 GB workstation graphics card -- the W9100.
Samsung's 5th-generation Android-based Galaxy smartphone includes a fingerprint scanner, updated camera and display, and water/dust resistance.
More:Blogs|News
Design News Webinar Series
3/27/2014 11:00 a.m. California / 2:00 p.m. New York / 7:00 p.m. London
2/27/2014 11:00 a.m. California / 2:00 p.m. New York / 7:00 p.m. London
12/18/2013 Available On Demand
11/20/2013 Available On Demand
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Apr 21 - 25, Creating & Testing Your First RTOS Application Using MQX
SEMESTERS: 1  |  2  |  3  |  4  |  5


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: April 29 - Day 1
Sponsored by maxon precision motors
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service