Interestingly enough, the way that I add information to the drawings was a cost-reduction thing, since debug time is expensive, much more than build time. So to make our planned profit we had to get things right every time. Adequate information helped a lot.
But really, if the individual doing the PCB layout does not understand what the circuit does, you can have some very interesting problems with board layouts.
William K, I agree with EVERYTHING you say. The effort you put forth makes for a good design. The effort put forth by the manufacturer in question was NOT sufficient to make a good design. When the schematic is not immediately available, a well designed component assists in fast troubleshooting or assembly. The product line in question does NOT.
I agree that the different connection schemes shown are not all intuitive. That is the case with a few makers of PLCs. The result is that when I create a controls drawing that includes a module, I put a "map" of the module right there on the drawing. Smetimes it just shows the terminal screws in the actual relationship, sometimes it includes more details. They always include the module nme, function, and number. In addition the address of each connection may be shown.
As to why they are arranged so strange, it probably has a lot to do with the internal circuit board and what components are installed on it. I have done PCB designs and sometimes getting the connections in the most desireable places is quite an effort. Also consider that the circuit board designer may not have a fraction of a clue about the circuit functionality. I have had that kind working for me also.
The problem is lack of experienced oversight, just like the recent BMW driver settings issue. One cannot expect to just go coding without proper guidance (from management and specification) and expect not to have a mess.
The issues described herein are especially grievous because those making the big bucks, if you will, are being paid those big bucks to know better ... and yet they don't. Hmmm ... maybe paying the big bucks really does NOT ensure quality of work. Oh what an epiphany!
If one is going to "spread out the work", one MUST FIRST establish the proper documentation and specificiation of the work to be done in comprehensive clear and certain terms. It is just insanity to do otherwise and, frankly, actionable IMHO as misuse and abuse of company resources. Not to mention that if someone is killed because of the resulting confusion in use, just because the OEM likely won't be sued makes it no less culpable. Life is dangerous enough without someone designing more in.
You're right jmiller; the project manager for the product should have caught this. I wonder if it was caught, just too late because molds were already fabricated.
Dave, thanks for responding in the spirit of the post! However, I think in light of new evidence, I must ask for a recess. I may have discovered new evidence of an even more egregious crime. The evidence submitted so far shows simple bad engineering. The new evidence, hopefully displayed next week, I hope you will find as proof of sabotage by the large manufacturer.
Often situations like this arise when there is no ownership of the platform or designs within the platform. I've heard stories of one group trying to reduce cost by changin materials while another group is making tooling changes in improve performance. Talk about trying to hit a moving target. Let's change to a material with a slightly different shrink rate while we are changing the tool. How can the supplier have any chance of success of meeting the tolerances on the print.
Mr. Right hand, meet Mr. Left Hand. Why don't you two take some time to get acquainted.
If there is one central ownership of the entire system/platform/design then all changes, new products, have to go through one group in order for alignment. Great concept, but it can slow things down and cost a little more.
This isn't just a lack of common sense; it verges on a sadistic desire to inflict mental anguish on anyone who has the misfortune to have to use this unit. Given the extreme maliciousness of this crime, I recommend the maximum penalty.
Agreed, Beth. The worst part of this is that it's so common. How many times have we all seen products get worse during the course of their evolution? New ideas don't necessarily make for better products.
Forget about the lack of common sense, this points up a much larger issue that many companies are still stuck with siloed design processes where one functional group or division doesn't have any idea or ability to tap into work that's being done in another part of the company.
If this is their best excuse: "The best answer I could get from a representative of this manufacturer was "The electronics module [the device with the LEDs] was made by one branch of the company, while the base and terminal block were made by a different branch."--that's pretty darn scary!
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
New versions of BASF's Ecovio line are both compostable and designed for either injection molding or thermoforming. These combinations are becoming more common for the single-use bioplastics used in food service and food packaging applications, but are still not widely available.
Andrew Morris designed a circuit that could detect a stroke victim's groan and convert the sound into a signal so caregivers would know when help was needed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
0 
