HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Rob Spiegel
User Rank
Blogger
Re: What does this mean for US manufacturers?
Rob Spiegel   7/18/2011 11:18:16 AM
NO RATINGS
That's an excellent point, Dave. Those who oppose RoHS on scientific grounds do indeed discuss its danger (or lack of) in the product's useful life and after disposal. You're correct about the "birth" part where there would be plenty of exposure.

Dave Palmer
User Rank
Platinum
Re: What does this mean for US manufacturers?
Dave Palmer   7/15/2011 1:12:20 PM
NO RATINGS
I thought the whole point of RoHS was that it considers the product from cradle to grave.  The fact that lead may not leach out of a soldered joint in a landfill doesn't mean that the use of leaded solders is environmentally benign.  In this case, the risks are at the cradle, rather than the grave.  The same goes for chromate conversion coatings.  I don't think a chromated die casting presents much of a threat to the environment - but a a chromate line obviously does.

In my field (marine engines), we still use a lot of RoHS restricted substances, including cadmium, hexavalent chromium, etc.  We are actively looking for good alternatives, and already have a few in place.  The U.S. Department of Defense has actually a lot of helpful work in this regard.

There has been a lot of confusion in the U.S. about exactly what RoHS is, what it applies to, etc.  I'm sure that these changes will only increase the confusion.

Rob Spiegel
User Rank
Blogger
Re: What does this mean for US manufacturers?
Rob Spiegel   7/12/2011 5:51:23 PM
NO RATINGS
Good points, sensor pro. One of the reasons IPC fought so hard to make sure RoHS changes were based on proven science going forward is because many in the electronics industry criticized the banning of lead in solder, insisting that the EU didn't base the decision on proven science. Many materials experts insist the lead in solder won't leach out in a landfill and they have challenged the EU to prove otherwise, to no avail.

The fact that IPC won on this point during the RoHS Recast is significant.

sensor pro
User Rank
Gold
Re: What does this mean for US manufacturers?
sensor pro   7/12/2011 12:21:32 PM
NO RATINGS
This is the only positive news in this whole ROHS issue. We still produce for ourselves withoiut ROHS. I still see too mane peoduction issue which in my opinion dod not justify this ROHS mess. Just last week some connectors melted while in automatic assembly due to high temperature. They all were ROHS, however with a very borderline thermal chanracteristics. Now we need to look for an even more expensive part. We were producing this product to over 10 years without any problem. Now we have burnt connectors and overheated ICs. Also during rework, the ROHS solder smells terrible. I really fail to see any serious benefits. Am I the only one with negative views?

Rob Spiegel
User Rank
Blogger
Re: What does this mean for US manufacturers?
Rob Spiegel   7/12/2011 8:42:45 AM
NO RATINGS
If your markets are only in the United States RoHS has no affect. There are medical equipment manufacturers and many defense manufacturers who are not affected by RoHS. Global manufacturers, however, have adopted the RoHS restrictions since they don't know which of the products might end up on the European market.

The biggest change in the RoHS Recast is that some portions of the electronics market are no longer exempt from RoHS restrictions. That includes medical electronics. So, if you're a medical electronics producer with a global market, the RoHS restrictions may be newly applicable.

So far, there is no credible movement in the United States to create a domestic RoHS.

Beth Stackpole
User Rank
Blogger
What does this mean for US manufacturers?
Beth Stackpole   7/12/2011 8:05:54 AM
NO RATINGS
Seems like we've been hearing a lot about new RoHS guidelines as of late--I believe Rob, you wrote something recently about new regulations in India. My question is what does all this mean for engineering and manufacturing groups in the States given that Europe is obviously a key market for them and will these new stronger rules finally pave the way for similar and subsequent regulations here?



Partner Zone
Latest Analysis
Technology has proven over and over again to be tremendously empowering, to individuals and organizations alike. Misuse that power, however, and you might find yourself in big trouble.
Steadfast in its belief that diesel engines are right for the times, General Motors is expanding US availability of the compression-ignited technology in Chevrolet cars and light trucks.
Most cyber attacks could be avoided by adopting a list of Critical Security Controls that were created by the Center for Internet Security. That’s the message from Steve Mustard of the Automation Federation.
How 3D printing fits into the digital thread, and the relationship between its uses for prototyping and for manufacturing, was the subject of a talk by Proto Labs' Rich Baker at last week's Design & Manufacturing Minneapolis.
The term “range anxiety” began fading into the rear view mirror recently, as major automakers made announcements about longer-range, battery-powered cars.
More:Blogs|News
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Sep 12 - 16, Analytics for the IoT: A Deep Dive into Algorithms
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9 | 10


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Technology Marketplace

Copyright © 2016 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service