Good points Beth and Lauren. The solar cell applications would be long-term, 20 or so years. These types of parts are typically not recycled after their use. There are bigger fish to fry from a green perspective-- although the recycling of all plastics for every application is a good goal. The most recyclable plastics are those with basic chemistries and little complexity in the compound formualtion. That way they can be mixed, melted and have fairly predictable property profiles. The igus compounds are complex and proprietary. So I would doubt there is much realistic expectation that this component would be recycled. I love, however, when I am proven wrong. Note: virtually all plastics (even filled thermosets) are technicallyrecyclable. But the key issue is: Are the commercially recyclable?
The plasticsmaster blew my away with his detailed answer to Rob's question, and I think he hit the nail on the head. There haven't been any recent major breakthroughs in polymer chemistry, but the sophisticated refinements (along the lines of igus) have been amazing. Other big, enabling developments have come in processing technology.
Have plastics changed that much over the past 10 years? Absolutely, since I started keeping track of thermplastic materials in the early 1990's, the number of commercially available materials has grown from 50k to over 80k. Many of these are unique, formulated for a specific application then made commercially available.
how has plastic changed? Higher continuous use temperatures, stronger, longer life cycles, conductive, more efficient weatherability, and nanotechnology advances, just to name a few.
sustainability factor of the plastic part? Well, I'm a strong advocate of good plastic part design. There are so many plastic materials out there that I'd lean toward the optimistic possibility that there is a material that could withstand the required constraints surounding solar panel design (and being outside). Many times when a part fails, its more often due to poor design rather than poor material selection. Remember, I said "more often". There is, of course, always the exceptions where poor material selection WAS the culprit in the failure of the part.
is the plastic recycled? PA (Nylon) & PEEK are considered High Temp Materials. Also known as Engineering materials. I've seen recycled Nylon for sale, but not PEEK. There's a reason these materials are called Engineering materials. They have very unique characteristics that qualify them for high tech applications [in their virgin states]. When a material is reground for re-use, it loses some of its physical properties (it's been heated and sliced and diced once already). After a single regrind, some materials will lose up to only 2% of thier original qualities. Any more than that and most materials will go down hill quickly. So the liklihood of the solar bracket in this article being made from recycled materials is slim.
Being cheaper is a good thing, but are they really better?
Doing a bit of research on http://www.igus.com brought me to their brochure for the bearings that appear to be the product line that the bearings in the article were chosen from.
It appears as though extensive testing for these bearings have been performed, and for me the highest selling point is the predictable lifetime that the products state. This will allow engineers and maintenance to plan their downtime of systems relatively accurately, and since these are plastic components get the repairs done quickly as well.
I wonder about the sustainability factor of the plastic part being used to replace the metal. Solar panels are a green initative ... is the plastic recycled and does it do anything to improve the carbon footprint of this offering?
"The plastic part is 70 percent cheaper to produce than the previously used metal bearings. The part eliminates the need for lubrication. Lubricated metal bearings had attracted dust that required maintenance in remote locations. Also, the light weight of the plastic part simplifies installation." .... Seems like a no-brainer to me.
Have plastics changed that much over the past 10 years? If so, how has plastic changed? Apparently it has changed enough to replace steel in this application.
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
6 
