HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Comments
View Comments: Newest First|Oldest First|Threaded View
Dave Palmer
User Rank
Platinum
The case of the breaking brakes
Dave Palmer   6/24/2011 3:03:42 PM
NO RATINGS
Powder metal parts can cut costs, but (as with any material or process) it's important that there be a good match between the application and the material.  The award-winning parts seem to be good examples of this.

Unfortunately, I've also seen examples of parts which never should have been powder metal.  For example, I was once involved in a failure analysis for a mechanical brake actuator which consisted of a hub with a long shaft.  Since the compaction direction was along the axis of the shaft, and the length of the shaft was more than twice the diameter of the hub, it was difficult to achieve a high density in the shaft.  The shaft was subjected to torsion and bending loads.  Depending on the exact size and location of porosity, fatigue cracks would initiate at the base of the shaft.  With repeated actuations, the shaft would snap off, rendering the brake inoperable.

Making the part out of powder metal may have saved money in the short term, but this could have been a very expensive problem if anyone had been injured or any property had been damaged (fortunately, this never happened).  As it was, a significant sum of money needed to be spent on this issue.

Of course, there are PM techniques which could have been used to solve this problem.  For instance, double press / double sinter would have made it possible to achieve a higher density.  Powder forging would have allowed an even higher density.  But once the part was already in production, either of these options would have required significant new tooling expenditures.  Ultimately, after examining a number of options, it was found that it was cheaper to machine this part from an inexpensive forging.

There are many applications for which PM is a great option.  However, design engineers need to make sure that it is a good fit for the application.  PM suppliers should also be careful to bring up any potential areas of concern during the design review process, so that any potential issues can be resolved before the part goes into production.



Partner Zone
Latest Analysis
A Frost & Sullivan study finds that increased cyber attacks are prompting a flurry of innovative protection tools.
Devices and interconnected systems are finding a foothold not only in our homes but in mainstream organizations. Here are three tips to mitigate the risk.
What makes this movie stand out from the typical high school sports story is that the teenagers are undocumented immigrants, and the big game is a NASA-sponsored marine robotics competition. Like many other Hollywood movies, however, Spare Parts only tells part of the story. What the film shows -- and doesn’t show -- raises important issues affecting STEM education in the US.
Instead of sifting through huge amounts of technical data looking for answers to assembly problems, engineers can now benefit from 3M's new initiative -- 3M Assembly Solutions. The company has organized its wealth of adhesive and tape solutions into six typical application areas, making it easier to find the best products to solve their real-world assembly and bonding problems.
Load dump occurs when a discharged battery is disconnected while the alternator is generating current and other loads remain on the alternator circuit. If left alone, the electrical spikes and transients will be transmitted along the power line, leading to malfunctions in individual electronics/sensors or permanent damage to the vehicle’s electronic system. Bottom line: An uncontrolled load dump threatens the overall safety and reliability of the vehicle.
More:Blogs|News
Design News Webinar Series
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
12/10/2014 8:00 a.m. California / 11:00 a.m. New York
3/31/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Mar 30 - Apr3, Getting Hands-On with Cypress’ PSoC
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  67


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service