User Rank
Re: Expensive equipment requires a management plan
PaulMcNamara   6/28/2011 3:52:15 PM
Thanks Alexander.  It may seem hard to believe be ocassionally we find old vacuum tube equipment (or old equipment generally, even if it's not vacuum tube) piled away "just in case the program comes back".  While that concern does need to be cared for (and we do) the mentality of holding on / hoarding equipment is costly to the design engineer in ways they may not be able to imagine.  Thanks again for your post. 

User Rank
Re: Small Companies Too
PaulMcNamara   6/28/2011 3:48:37 PM
Thanks Jack. I couldn't agree more with what you say.  Large companies can be thought of as collections of smaller lab entitites  Often each lab has its own process, procedure and spreadsheet -- almost identical to what you are talking about.  We've actaully got a refined set of processes, supported by software tools and including people strategies.  While we often write about the "big guys", as you say, the approach works for smaller companies as well.  We are working on a couple of new offers that are scaled but but we think we will helpful to smaller companies.  Thanks again.

Jack Rupert, PE
User Rank
Small Companies Too
Jack Rupert, PE   6/28/2011 3:17:01 PM
Excellent article Paul.  The need for a holistic approach is necessary on the other side of industry too, where you're not dealing with $100M setups.  In those cases, however, the problem is not so much of the wrong approach being pushed down from above, but rather no unified approach whatsoever. Equipment, procedures etc. are just procured on as-needed basis and nothing is tied together.

Alexander Wolfe
User Rank
Expensive equipment requires a management plan
Alexander Wolfe   6/23/2011 5:25:09 PM
Thanks for an informative article, Paul. Given the cost and sophistication of modern test equipment, a holistic equipment management strategy is essentially mandatory. At the same time, an article like this makes me fondly recall the old days, working with tube-based oscilloscopes. The test-equipment management strategy back then was, if the equipment acted up, you gave it a good whack on the side.

Partner Zone
Latest Analysis
Digital design tools and 3D printing can be used to innovate new products and accelerate the development and commercialization cycle.
The ways companies and their outside product development partners work together and divvy up success are evolving radically. Here's what you need to know no matter if you are an engineer or executive.
One of the biggest walls in embedded software development is the integration of low-level drivers with higher-level middleware and application code, but silicon vendors are stepping up to bring it down.
Honeywell and NASA's FMA Live! Forces of Nature show uses hip-hop to teach physics lessons and is currently on its Fall 2015 tour in the Midwest.
Using 3D-printing to integrate electronics is an enthralling idea, but there's a long road ahead to commercialization.
Design News Webinar Series
10/1/2015 11:00 a.m. California / 2:00 p.m. New York
9/10/2015 11:00 a.m. California / 2:00 p.m. New York
8/13/2015 11:00 a.m. California / 2:00 p.m. New York
6/25/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 5 - 9, Standards for the Internet of Things (IoT)
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service