It is management’s job to define the desired product attribute list including assigning a weighted importance to each attribute from costing to FMEA and everything in between. It is then clear to the engineers how to approach a first article or straw man. Efficiency can only be realized if an early focus is placed on the weighting of attributes, not just the desired attributes alone.
Likely constraints and exceptions will start to be discovered early in the process from this point on and without a closed loop to management at this point, things can go wrong quick. Focus on the weighting of each attribute more than the attributes themselves, as this process, done right can elicit new and as of yet unthought of attributes by simple material and process evaluation.
Also, the engineers must keep in mind the end user documentation for the product, as many times attributes can be improved by better documentation and signage on the product in lieu of adding costly physical elements in the mash up (not so much these days with safety attributes IE “keep hand out of blades” doesn’t cut it anymore).
Management will ultimately decide on the weighting and will likely alter the weighting based on engineering’s ability to match the weighted attributes and solve for constraints and exceptions in unique ways.
I usually get to commission my projects, so get feedback from the initial operator. I also frequently get to see the systems after 6 months to a year, and thus get to learn what I did wrong and improve future designs.
As much as I'd like to dream about the "ideal" design process - collaborative and streamlined - some new product projects end up more like a battle between departments and egos. I have managed many projects where no matter how well the plan is conceived, specified, documented, managed, and implemented, it all boils down to how the executive group views the R&D process and nurtures the development team. Most manufacturing companies that I have worked for, treat the development process/team as a luxury, a kind of necessary evil that saps valuable resources away from more interesting, glamorous, and quick-revenue generating opportunities.
On a positive note, I have experienced a few projects where the executive team member clearly stated the general goals for the project and expectations for each team member. Nothing too complex or demanding, just plainly stated, in-writing, and communicated to the team, in-person. Sometimes the exec would leave the team alone and only make an appearance when asked, or for milestone presentations. Again, this is a HUGE topic (or set of topics) and I've experienced a wide array of functional / dysfunctional teams and management groups.
I'd like to hear stories from other readers about how other companies and individuals experience the development process. The good, the bad, and the "what ifs?"!
You raise some interesting points around getting feedback loops earlier in the design process. I know the DFMA Forum was also home to some lively discussion around applying lean and DFMA practices early in design to help drive down the cost of products and level the playing field when it comes to outsourcing. Stay tuned to my story on how these kinds of engineering workflows can accelerate and support the effort to reshore manufacturing back to US soil. Should be up on the new Design News site shortly!
One simple solution that springs to mind is the correct use of FMEA's.
A good FMEA should weed out the unintended consequences of a design, the problem is most engineers see FMEA's as a chore which is boring but has to be done to tick the box, if taken seriously and fully engaged with an FMEA can really help the design process, and has to be done early enough that the solutions can be implemented or the design is not cornered.
So you software people, make FMEA software that interacts with the design process easier and intuitivley and can be worked on in collaboration whilst the design is on-going, rather than making the team lock themselves away in dark room and go through a laborious catch up of all the things they've thought of or done anyway but not recorded.
What's needed for design problems like this is a feedback loop that alerts the design team of the unintended consequences of a design. The problem with the fuel overfill could be easily solved if the design team is aware of the problem.
One simple solution is for the design team to go online and find comments by frustrated users who are pulling their hair out over design problems. Comments on online forums pop up quickly when users run into design SNAFUs.
Altair has released an update of its HyperWorks computer-aided engineering simulation suite that includes new features focusing on four key areas of product design: performance optimization, lightweight design, lead-time reduction, and new technologies.
At IMTS last week, Stratasys introduced two new multi-materials PolyJet 3D printers, plus a new UV-resistant material for its FDM production 3D printers. They can be used in making jigs and fixtures, as well as prototypes and small runs of production parts.
In a line of ultra-futuristic projects, DARPA is developing a brain microchip that will help heal the bodies and minds of soldiers. A final product is far off, but preliminary chips are already being tested.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.