Toyota's NS4 will employ a human-machine interface built around a multitouch screen with the look and feel of a smartphone. Toyota is forming alliances with Microsoft and Intel to create seamless vehicle interfaces.
(Source: Toyota Motors)
I had a new 1969 Dodge Dart with a Factory 383 Magnum. I don't think Grampa would have bought this car. Build quality was ok but not perfect. The car was extremely fast for the time and sent many a Camaro and Mustang home with their tails between their legs. Reliabity was fantastic. I ran this car hard for several years until the Arab Oil Embargo, when I traded it in for a VW Beetle (big mistake). Todays Chrysler products are the children of German influenced engineering and their idea of what a car should be. I refuse to accept a 4-door Dodge Charger, no matter how well it performs. I was hoping for a two door coupe when the company changed hands a few years ago, but so far it hasn't happend.
For a whole variety of reasons, I believe American consumers trust Detroit again -- either that or they have let go of their preference for Japanese cars. When GM became the top automaker again last last year it came as quite a surprise.
You're right, Rob. Detroit started to improve in the '80s. But they also wouldn't admit they had had quality problems until about 10 years later. Because they refused to publicly acknowledge their earlier problems, many Americans refused to trust them, even when they started building good cars.
1977 was likely one of the worst years for American cars. I owned a mid-1980s Cutless and it was a very good car. Before that I owned an early 1980s Pontiac 6000. It had more problems than the Cutless, but it was a pretty good car. Looking back, the Cutless was probably superior to the 6000 simply because it was mid-1980s instead of early 1980s. Detroit was begining to improve through the 1980s.
That's an interesting difference, between the parts and how they go together. My first, second, and third cars (I keep them a really, really long time and don't drive much) have been Japanese from the get go. They are superior machines and Japanese carmakers have been listening to their customers since at least the 70s when they started accommodating American tastes and body sizes.
Rob, I remember the Cutlass all too well. I had a '77 Cutlass with a catalytic converter problem that caused to vehicle to balk when I'd hit the accelerator. After a 15-minute warm-up, it would operate normally, but I didn't always have time to warm it up for 15 minutes. It also had widespread, unrepairable electrical issues. Other than that, it was a pretty good car.
The Center for Automotive Research has claimed that the key to automotive reliability lies in the difference between a philosophy of "perfect parts" versus "perfect system." American automakers, they say, strive to use perfect parts, while Honda and Toyota place less importance on the parts themselves, and greater importance on the way they go together. See:
From what I hear, it's not Chrysler's designs which are at fault, but the build quality. I know someone in their minivan groups who's justifiably proud of their engineering work, but then at the same time I hear stories like that of a couple who went to a Chrysler dealer, and she cut her leg on the edge of a plastic banner that didn't have the edge smoothed down. No sale.
Chrysler's designs do win accolades but the company has consistently fared poorly in Consumer Reports' reliability studies. The poor performance continues even today, and the CR studies are an important measure, since they base their studies on approximately 1.4 million user responses.
I feel your pain, Alex, as my family suffered from a couple of lousy Chrysler purchases in the `80s as well and as a result, became Detroit-adverse when it came to buying cars. It's an unfortunate mindset, which didn't seem to have the same repercussions then as it does now to the long-term health of the American car industry and the overall recovery of the American economy.
That said, and with the work done in recent years by the U.S. auto makers, that mindset should admittedly should be revisited, especially when it comes to said OEM, Chrysler. That's one company that has consistently turned out an admirable crop of designs, from the redone Jeep series, which is not only good looking, but drives great (my husband had one) to their 300 sedan series, which consistently wins accolades.
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
7 
